Jump to content
SAU Community

Recommended Posts

Ok guys,

I want to put on my Momo wheel. So this afternoon,

I managed to get my steering wheels off, piece of cake.

Saw the centre hexagonal locking nut. Sprayed some WD-40 on it, and it wont budge at all..... bugger.... @#$%

I tried using socket 17mm (the largest one I had) but won't fit. I use 3/4" but seems to be just a little bit loose there. Maybe this cause a bit of difficulty turning the socket wrench and the nut won't unlock.

Anyone can help me, whoever done this before, what socket size you use? Metric or Inches system? Is it 18mm or 19mm????

Thx.

Rianto

Link to comment
https://www.sau.com.au/forums/topic/10512-steering-wheel-centre-lock-nut/
Share on other sites

Gday rs73

I have done this a while ago when I had trouble with my Hicas light coming on. Steering angle sensor was the problem.

I am fairly sure that I used a 3/4 socket. You need a bit of leverage to undo it and I used a Torque wrench with about a 600mm handle.

I am not sure from your comments, but if the socket is stuck on the nut then it certainly is too large.

Once the nut moved I counted the number of turns that it took to come off completely so that it went back on the same.

You will need a steering wheel puller after it has come off. Don't be tempted to bash it with a hammer or something.

Make sure you have a boss kit for our R33 otherwise you will have the Hicas warning light coming on and it will be disabled.

Hope this helps and other guys may be able to confirm socket size etc.

Good luck

El Bee

Thank's guys...

I did use 3/4" but it's a bit loose, probably need to find a metric 19mm socket as 3/4" is 19.05 mm, that .05 mm might make a difference. And of course, I got HICAS boss kit.

I don't have 600mm wrench handle, so might be a good idea to find one, mine is short only like 200mm so I guess won't help me give more torque to the nut. And I'll try spraying more WD40 again, may not be long enough last time...

mine's a lousy socket set bought $27 at bunnings. I dun think it will hold that much, I'm more worried in breaking the lock in the steering mechanism (when you turn off ignition) than the rachet itself. might need someone to hold the steering steady for me.

19mm socket and some muscle. Done it a few times on my car.

To get the wheel off, undo the nut, but not all the way. Sit in the seat with your hands either side of the wheel, and try to pull it off 1 hand at a time, so you are forcefully wiggling and pulling the thing. Thats what I have to do with mine, you cant pull it straight off, have to wiggle it. Leaving the nut on stops you pulling it off and smashing yourself in the face with it or something else unpleasant.

This seems to sound very difficult to do... how did those guys at nissan put these steering wheels on our cars, pound 'em in with a huge sledge hammer???

If after all means I still can't get the centre wheel lock nut off or can't yank off the steering wheels, anyone know a good place in Melbourne who has done R33 with HICAS? I dun wanna some "yea, we can do that - they're all the same" backyard accessories shop around the corner mess up my HICAS sensors...

  • 4 weeks later...

I finally gave up and ran to the local mag & tyre shop. They had this "HUGE" massive 60 or 80 cm long wrench, and angle adjustable. Took them 1 minute to undo the centre nut!

They finished off the installation and cost me a $20 total, nice blokes from sth africa where they came from.

The end result is:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...