Jump to content
SAU Community

Recommended Posts

thanks for that guys, im looking at skylines at the moment, though im just sorting through all the shit cars, there are so many dogs out there. Trying to find one half decent b4 i look seriously at it. will def pm/ring when im going to look into more detail at the car!

Cheers, Tyson

Link to comment
https://www.sau.com.au/forums/topic/105732-32-help/#findComment-1953395
Share on other sites

Check the undercarriage for dodgies.. be careful of ones where the paint looks *too* good, as a cheap job may look good now, but in 6-12 months start bubbling up as more than likely it will be a cheap job (some dealers nearly respray all stock). It will be near 15 years old, not many cars have immaculate paint jobs by then.

Otherwise just take it for a drive, check for clunks, floaty steering, make sure the brakes pull it up well. Check for crunches in the gearbox, clutch engages freely, even tyre wear, and oil leaks, particularly under the engine (rb20's love to leak when old - and usually its a bitch to fix).

Oh, pull off some of the intercooler piping (or AFM), and check for accessive oil in there. If there is any more than a tiny amount, definitely don't buy it.

Link to comment
https://www.sau.com.au/forums/topic/105732-32-help/#findComment-1954442
Share on other sites

You can check that pipe.. or main intake pipe that goes to manifold.. Basically if there is a *lot* of oil in there (as in you can see it dripping off your fingers), there is oil from the sump blowing past the piston rings during each combustion stroke. Meaning the piston rings are worn.

This pretty much means there isn't too much life left in the motor as it'll only get worse and worse until something gives way.

It can also mean that the turbo is going, letting oil into the system -- again whilst not as bad as piston rings, probably not a great thing.

Anyhow, that is my explanation... :)

Link to comment
https://www.sau.com.au/forums/topic/105732-32-help/#findComment-1959522
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...