Jump to content
SAU Community

Recommended Posts

righto fellas what do i need.

aim for the car is 300-350rwhp

mods will be fmic, pfc, ebc - 12psi, full exhaust 3" - dump is twin pipe version, timing is at 20 degrees, pod filter with CIA.

other mods aren't performance based.

been told either of the following will do

bosch 044, 975 or 985.

input welcome

Link to comment
https://www.sau.com.au/forums/topic/10615-fuel-pump-upgrade/
Share on other sites

Some newbie questions if I may...

* How much rwhp (or rwkw) can the standard factory Fuel pumps handle ?

* Obviously the more power the more fuel required and the stock pumps are only good to pump so much fuel ? Anything else worth knowing... ?

* What is the typical cost and can anyone post some websites with info/products/prices ?

thanks,

Ben.

Link to comment
https://www.sau.com.au/forums/topic/10615-fuel-pump-upgrade/#findComment-170835
Share on other sites

You might find it a bit cheaper to go a second hand GTR pump, can get them for 250-300 compared with 500 for a 044.

I have those mods, and I am only making [email protected], at the time it was about 35deg C. What turbo are you getting?

Currently the injectors are starting to show the strain too(up 82.9% when tuned with a Z32 afm, 77.7% when not so well tuned with a sock afm but that was pushing out 191rwkw and pretty lean), so you may want to think about a rising rate reg too.

sorry I'm rambling a bit.

Benm, sydneykid answers some of your quesions on the SDU forum, a thread entitled 600hp fuel system, here is a link

http://forums.skylinesdownunder.co.nz/show...50&goto=newpost

Hope it works as I cant get on to the SDU forum at the moment, bloody server too busy.

Steve

Link to comment
https://www.sau.com.au/forums/topic/10615-fuel-pump-upgrade/#findComment-170847
Share on other sites

Findings from a trusted source differ to that in that link posted above.

I've got a 975 mounted internally in my car.

Begin Cut and Paste

The big daddy Bosch Motorsport pump is part numbered 0 580 254 044, it can flow

330L/hr @ 73.5psi and price is $550.95

The last 3 digits will be different for other Bosch pumps.

975 is a 228L/hr flow @ 73.5PSI at $340.95.

984 is the same as 975 just that the fittings are slightly smaller.

040 is 235L/hr flow @ 73.5psi and it comes with a screen for in tank operation and is priced at $359.95.

910 is 200L/hr flow @ 73.5psi at $229.95.

I know that although the 975 doesn't say its a in tank pump, it can be mounted

internal or external to the tank, maybe all the other Bosch pumps can be

mounted internal or external also.

End Cut and Paste

Link to comment
https://www.sau.com.au/forums/topic/10615-fuel-pump-upgrade/#findComment-173146
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...