Jump to content
SAU Community

Recommended Posts

ok, anyway after some months with my engine out of my gtr, its time to re install..

now, ive searched and searched for the best and most efficient way to do this, with no luck finding anything, i need some assistance

we have looked, and cant decide, wether it will be easier to remove one driveshaft? both drivshafts or none?

we had a trial run, but were pretty sure we cant get the drivers side driveshaft in, and the clutch lined up with the pass driveshaft as they clash when trying to line up the 2 splines.

any advice will be much appreciated and or tips, but please, i want to know definate ways, not just , well i think it will be easier because in my mind it would work that way, i want people to reply who have put the engine back in etc

Link to comment
https://www.sau.com.au/forums/topic/106892-rb26dett-engine-install/
Share on other sites

ok, anyway after some months with my engine out of my gtr, its time to re install..

now, ive searched and searched for the best and most efficient way to do this, with no luck finding anything, i need some assistance

we have looked, and cant decide, wether it will be easier to remove one driveshaft? both drivshafts or none?

we had a trial run, but were pretty sure we cant get the drivers side driveshaft in, and the clutch lined up with the pass driveshaft as they clash when trying to line up the 2 splines.

any advice will be much appreciated and or tips, but please, i want to know definate ways, not just , well i think it will be easier because in my mind it would work that way, i want people to reply who have put the engine back in etc

She will go in the same way you took it out !! I usualy take engine + box out as one unit and put them back in the same way .

I dont understand what you on about driveshafts, the pass you undo the 6 bolts an dleave it there . The drivers side you either have to pull out or drop the lower control arm and slide it out so you can lift the donk out . Put it back the same way as you took it out dude as simple as that . I usualy assemble everything on the engine before i put it in .The air cond pump and power steer pump i tie on the car on the pass side and leave them there .

If you still have the box on the car you will have to drop the box mount down so u can do up the top bolts just like you did to undo them . As for the clutch you have to make sure you line it up with either a tool or an old input shaft ! If its not lined up well you wont be able to bolt it on .

hrmm, thats what i suspected, but it just doesnt seem to be working ...

we didnt need to pull box out, so we didnt.

this is on r32 not sure if it would make much diff between 33,34...

we will give it another go tomorow nite, the clutch was lined up using tools. however, not sure if spline is 100% correct but nothing that cant be wriggled into it

hrmm, thats what i suspected, but it just doesnt seem to be working ...

we didnt need to pull box out, so we didnt.

this is on r32 not sure if it would make much diff between 33,34...

we will give it another go tomorow nite, the clutch was lined up using tools. however, not sure if spline is 100% correct but nothing that cant be wriggled into it

You are going to have to undo the box so you can twist it around , thats why i take out engine box together , some people just drop the box under the car, i find it easier to take out engine box together , each to their own . 32 , 33 +34 all the same, i've done them all .

ahh ok kool. well the problem with just leaving box out is that were doing this on a driveway due to lack of work space in garage.so we have to be able to push car in/out as need be.

we will prolly be doing it this arvo/night provided the rain stays away. but thanks for your assistance

ahh ok kool. well the problem with just leaving box out is that were doing this on a driveway due to lack of work space in garage.so we have to be able to push car in/out as need be.

we will prolly be doing it this arvo/night provided the rain stays away. but thanks for your assistance

Its not easy on the floor, if you had a hoist would be much easier . You may have to jack the car up on stands as high as you can unbolt the box and sit it on a jack ( you may have to chain it on to the jack ) .Drop the donk in place and do up the 14 mm nuts on the engine mounts then try to bring the box up to the engine, it maybe better to put something under the front of the engine sump so the engine leans back as much as possible that should make life easier for you .

Now you can see why i take out engine + box as one unit much easier but you have to lift the combo a lot higher to get it in .

If you need any advice while you are doing it pm and i'll give you my number, i may be able to help if you get stuck .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...