Jump to content
SAU Community

BOV Ajustment


Recommended Posts

Guest RedLineGTR

I have a hybrid BOV on a skyline r33 gtst it vents to Atmosphere and Plumback, the question is that when the spring is adjusted so it not tight lets say 3 or so turns from loose, when the turbo starts making boost at 2500 it makes a flutter noise and when higher than 3000 it's normal whoosh sound, when adjusted tighter at 2500 doesn't make that much noise maybe a little whoosh and a 3000+ normal whoosh..Is it okay to leave it softish or is it better to leave it abit tighter. The tighter it is, will it make the BOV shut faster??

Thanks

Link to comment
https://www.sau.com.au/forums/topic/10785-bov-ajustment/
Share on other sites

The flutter ive been told is a bit of pressure hitting the turbo impellers when theres not enough air velocity for it to come rushing out of the bov in a hurry (eg over 3000). Obviously the pressure on the impellers is what the bov is meant to be preventing, however ive also been told at a low RPM its of little consequence.

I have a TurboXs BOV that has the same behaviour.

Red17

Link to comment
https://www.sau.com.au/forums/topic/10785-bov-ajustment/#findComment-175340
Share on other sites

It should be fine, I run a TurboXS BOV on my R33 gtst and the it does the job really well high up in the revs and the compressor flutter low in the revs should not damage the turbo. This is simply because there is not enough boost and it cannot expel the minimal amount of air via the BOV.

Link to comment
https://www.sau.com.au/forums/topic/10785-bov-ajustment/#findComment-178079
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...