Jump to content
SAU Community

Recommended Posts

Ok guys iv been posting questions in here for a while an i figure i may aswell post some pics an specs up of it.

I am the first owner in Aus an when i bought it it had a Full URAS monkey magic kit, coil overs, Mechanical diff east bear mirrors and 3" zorst since then i have done the following.

FMIC

Custom 3" dump with divided gate

Full 3" zorst

Bosch 040 fuel pump

Brass clutch with srung centre

Power FC

GTR injectors

GTR Radiator

HKS 2510 turbo with braided lines

GFB atmo boost controller

R32 airbox with HKS panel filter

Plumback with custom mounts

Also bought a heap of tyres lol

Cheers Jamie

post-15053-1142151652.jpg

post-15053-1142151681.jpg

post-15053-1142151719.jpg

post-15053-1142151775.jpg

Link to comment
https://www.sau.com.au/forums/topic/109305-my-cefiro/
Share on other sites

Every 2nd inported cefiro i see has those SSR rims (rears in pics) mine came with 4 of them and also those bling bling Ben Hur spike spinner things.....

Anyways nice ride.... yeah how did u source that URAS kit....NOONE has one of those :P j/k's

Nice Ride!

Link to comment
https://www.sau.com.au/forums/topic/109305-my-cefiro/#findComment-2013710
Share on other sites

hey guys thanks for the comments. Konnect not really ring DMD in brisbane have them in stock. R33Deviat not wrong i no when i first got it there were not many cefs gettin rd with monkey kits now ecery second 1 has it. Also how do we become a member of cefiro oz as i would love to join.

Cheers Jamie

Link to comment
https://www.sau.com.au/forums/topic/109305-my-cefiro/#findComment-2013733
Share on other sites

hey guys thanks for the comments. Konnect not really ring DMD in brisbane have them in stock. R33Deviat not wrong i no when i first got it there were not many cefs gettin rd with monkey kits now ecery second 1 has it. Also how do we become a member of cefiro oz as i would love to join.

Cheers Jamie

sarcasm....

Link to comment
https://www.sau.com.au/forums/topic/109305-my-cefiro/#findComment-2013813
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...