Jump to content
SAU Community

Recommended Posts

1993 Nissan Skyline GTS25T black, approximately 136,000km's, engine rebuilt at 80,000 with ceramic coated pistons and custom work (as supplied does 12s quarters). This car has been setup for track and road use and has been used as an every day vehicle (runs reliably despite the large power output), list of modifications are as follows:-

Front and rear suspension replaced with Koni and Bilstein's, lowered

OS Giken 2-Way Superlock LSD

OZ Racing 17" rims 255 rear 235 front currently running Toyo PROXES RA1 with plenty of rubber

Carbon fibre aero bonnet (three outlets and airpod intake) with bonnet pins and normal locking mechanism

3" complete exhaust system with APEXI N1 muffler

Hi-flowed turbo

Large K&N air filter with front air duct piping (both bonnet and spoiler)

Large custom front mount intercooler

Modified plenum

Davie's Craig electric fan

Oil catch tank

PWR race radiator rated at 700HP (all hoses replaced and new clamps using Redline Water Wetter)

Greddy Turbo Timer

APEXI AVC-R (boost controller with solenoid)

APEXI boost and exhaust temperature guages (pillar mounted)

Tweaked MINES ECU

Heat exchanger, water pump, power steering hoses, steering bushes, rear discs and pads (Pagid Blue's recommended, already using silicon race brake fluid) and airconditioning motor has all been replaced recently

Alpine remote control 3CD In Dash stereo (four speakers and two tweeters)

Climate control

Central locking and alarm/immobiliser

Sparco Pro 2000 race seat

Car at night looks like the space shuttle

Not on the car but sold with them

Set of four Black Super Advan 18" rims 265 with Yokohama DNA rubber (brand new)

Original bonnet

Car is road registered and has permits for the carbon fibre bonnet, PWR radiator, strut brace and air filter.

Sacrificed at $20K.

Car is located in Perth, Western Australia and well worth a viewing, enquiries call 041 999 1911. Serious buyers only.

post-2371-1142850699.jpg

post-2371-1142850732.jpg

post-2371-1142850762.jpg

post-2371-1142850796.jpg

post-2371-1142850822.jpg

post-2371-1142850856.jpg

Edited by el-ricardo
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...