Jump to content
SAU Community

Recommended Posts

Hey Guys... this is my 32 4 door.... Work VS KF rims, White, Rb25....

4 DOOR SKYLINE GTS-T

R33 2.5 ENGINE & BOX

POWER FC WITH HANDHELD

HKS 25/30 TURBO

HKS DUMP PIPE

HKS TWIN PLATE CLUTCH

HKS STAINLESS EXHAUST SYSTEM

7 POINT EARTH KIT

SPLIT FIRE D1 COILS

FACTORY SUNROOF

CUSCO FULLY ADJUSTABLE SUS

CUSCO UPPER & LOWER CONTROL ARMS

CUSCO SWAY BARS

CUSCO ADJUS CASTER RODS

CUSCO FRONT AND REAR UPPER AND LOWER STRUT BRACES

BN SPORTS SIDE AND REAR SKIRTS

NEW BN SPORTS KIT

FULL GTR BRAKES UPGRADE

GTR FUEL PUMP

GTR FRONT GUARDS & BONNET

10" REAR AND 9.5" FRONT RIMS

GREEDY OIL COOLER + REMOTE OIL FILTER KIT

FULL SET OF GREEDY-GAUGES

NISMO 2 WAY MECHANICAL LSD

PWR COOLER WITH STAINLESS PIPING

BLITZ ELECTRONIC BOOST CONTROLLER & TURBO TIMER

3 CORE RADIATOR

PILLAR TENSION ROD

MOMO STEERING WHEEL

8 POINT CAGE

Call me on 0405711000

Gold Coast

$22.000 ono

post-14955-1145512659.gif

untitled7.bmp

post-14955-1145512774.jpg

post-14955-1145512786.jpg

Edited by VIP32
Link to comment
https://www.sau.com.au/forums/topic/114271-r32-with-rb25-4-sale/
Share on other sites

Yes, Power is 310HP at the wheels at charlies motors in brisbane. about 80,000 on the engine. Just had timing belt and tensioners etc done for safety as it has just had a major service. Runs beautiful and has a knock of 12 at 1.2 bar of boost. Great strong engine. Needs to go asap. Needs cash bad.

my rotas running around the same power (only 8psi tho) yours sounds perfect for wat i want ive PM'd u back :worship: 310hp is around 220rwkw? hrmm mate here is making 248rwkw ( 350ish HP) with pretty much same set up but rb20

had compression check?

No Have had no Compression Test. THe Car made that power on 1 bar of Boost at charlies motors in brisbane which is slightly under rated as they dyno there cars with no compensaters. It is capable of 1.3 bar or boost. Now has 6 months rego and a spare GTR front bar.

would you swap it for a r32 gtr 92 model

very very very clean in an out

hks air filter an cam gears

trust suspension

bbs rims 17''

2510 turbos

apexi / blitz exhaust

apexi power fc

os giken twin plate clutch / flywheel

if your keen let me know ill send pics via email

Edited by LEANBAC

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...