Jump to content
SAU Community

Recommended Posts

Hey Guys... this is my 32 4 door.... Work VS KF rims, White, Rb25....

4 DOOR SKYLINE GTS-T

R33 2.5 ENGINE & BOX

POWER FC WITH HANDHELD

HKS 25/30 TURBO

HKS DUMP PIPE

HKS TWIN PLATE CLUTCH

HKS STAINLESS EXHAUST SYSTEM

7 POINT EARTH KIT

SPLIT FIRE D1 COILS

FACTORY SUNROOF

CUSCO FULLY ADJUSTABLE SUS

CUSCO UPPER & LOWER CONTROL ARMS

CUSCO SWAY BARS

CUSCO ADJUS CASTER RODS

CUSCO FRONT AND REAR UPPER AND LOWER STRUT BRACES

BN SPORTS SIDE AND REAR SKIRTS

NEW BN SPORTS KIT

FULL GTR BRAKES UPGRADE

GTR FUEL PUMP

GTR FRONT GUARDS & BONNET

10" REAR AND 9.5" FRONT RIMS

GREEDY OIL COOLER + REMOTE OIL FILTER KIT

FULL SET OF GREEDY-GAUGES

NISMO 2 WAY MECHANICAL LSD

PWR COOLER WITH STAINLESS PIPING

BLITZ ELECTRONIC BOOST CONTROLLER & TURBO TIMER

3 CORE RADIATOR

PILLAR TENSION ROD

MOMO STEERING WHEEL

8 POINT CAGE

Call me on 0405711000

Gold Coast

$22.000 ono

post-14955-1145512659.gif

untitled7.bmp

post-14955-1145512774.jpg

post-14955-1145512786.jpg

Edited by VIP32
Link to comment
https://www.sau.com.au/forums/topic/114271-r32-with-rb25-4-sale/
Share on other sites

Yes, Power is 310HP at the wheels at charlies motors in brisbane. about 80,000 on the engine. Just had timing belt and tensioners etc done for safety as it has just had a major service. Runs beautiful and has a knock of 12 at 1.2 bar of boost. Great strong engine. Needs to go asap. Needs cash bad.

my rotas running around the same power (only 8psi tho) yours sounds perfect for wat i want ive PM'd u back :worship: 310hp is around 220rwkw? hrmm mate here is making 248rwkw ( 350ish HP) with pretty much same set up but rb20

had compression check?

No Have had no Compression Test. THe Car made that power on 1 bar of Boost at charlies motors in brisbane which is slightly under rated as they dyno there cars with no compensaters. It is capable of 1.3 bar or boost. Now has 6 months rego and a spare GTR front bar.

would you swap it for a r32 gtr 92 model

very very very clean in an out

hks air filter an cam gears

trust suspension

bbs rims 17''

2510 turbos

apexi / blitz exhaust

apexi power fc

os giken twin plate clutch / flywheel

if your keen let me know ill send pics via email

Edited by LEANBAC

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...