Jump to content
SAU Community

Water Leakages And Wierd Vibration When Clutch Is Engaged.

eMsta

By eMsta,
in General Maintenance

 Share

Recommended Posts

eMsta Grand Master

eMsta

Posted
Posted

Hi Guys,

My baby is getting wierder and wierder. For the most she drives well, but last night whilst coming back from work something strange happened. The engine was warmed up - i let it warm up for a good 7 minutes before i started driving. But when the lights turned green, I tried to take off (not pushing her hard, but not soft either), and it started to vibrate. Almost felt as if it was the clutch/drive line that was not engaging. Alternatively, it could be the brakes, because I had this problem in my old accord. Any Idea what It could be? It only happend that once last nite, but I do recall it happening before - just that it wasnt as bad as last night.

The other thing is, my rear indicators are condensing, and leaking like anything. I have ordered new lights from japan - but thats only for the left rear - as there was a crack. The right side is leaking too and I dont know from where. What can I do about this? In addition to this - water seems to leak into the trunk too. Again, I am not sure where this is leaking from - but its worrying as the last thing I want is rust.

I need some advice as to what I can do. I can take it to the dealer, but I was thinking of doing all that, when I go to get my lights. Should I wait till then, or should I go asap?

Thanks guys! :)

MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

water usually leaks into the boot through a broken seal on the tail lights. to fix, just remove the tail-lights and put some silicon sealant around where the original sealent is (the gooey black stuff), and put it back, this should fix it.

don't bother taking it to a dealer, just a mechanic would be fine. Not too sure on the clutch problem, but i can imagine a warped flywheel or farked clutch could cause what you describe

RANDY Veteran

RANDY

Posted
Posted

There isn't any possibility that you started in 3rd is there? My gf learnt manual in my car not long ago, and it makes that shuddering and vibrating noise when the gear is too high for what you are doing.

I have seen the water leak fixed with Merlin's suggestion, that's the simplest option to take.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...