Jump to content
SAU Community

Pair Of Hks 2530's

justinfox
 Share

Recommended Posts

justinfox Mentor

justinfox

Posted
  • Author
Posted (edited)

Guys I have had a lot of PM's in regards to these turbos. I have no idea about the technical aspects, housings turbines etc all I know they are HKS 2530's!!! LOL. What you see in the pics above (pics are of the exact turbos).

UPDATE: On sale again due to time waster!!! I have gone and done the right thing and taken both turbos to Mark (head guy) at GCG. He has inspected both turbos and says both are in good working order.

I would be more than happy to go to GCG with you, and the turbos, so you can hear it from Mark's mouth.

$2k for both now that I have Mark/GCG's assurance that both turbos are fine (ie: he says a tiny bit of shaft play on both which is totally normal for ball bearing turbos and no oil leaking at all from the rear of either turbine).

Edited by justinfox
justinfox Mentor

justinfox

Posted
  • Author
Posted

Sorry, I am in Sydney. Turbos are currently in Padstow just 5 minutes from GCG. So happy yo meet up in Padstow, then go to GCG for a live inspection/approval.

PS: No receipt for the rebuild! I can't find it (I've turned the house absolutely upside down looking for it, no luck).

Both turbos have been stamped though, with a metal GCG plate with numbers on it which must correspond to GCG's files? I am not sure, but Mark knows the turbos and remembers me and my ripped off on SAU story so all good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Dose Pipe Sutututu
      Intercooler Choice

      By Dose Pipe Sutututu · Posted

      Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...