Jump to content
SAU Community

Recommended Posts

guys... have u ever bought turbo, manifold, and wastegate from this site

http://www.monstaperformance.com

the price seem reasonable.. but i have doubts that it's for real...

so has anyone used their products? what are yout comments??

1big.jpg

MonstA T3/T4 600HP TURBO $499 S/H$29

The T3 / T4 MonstA Turbo are custom matched for specific applications. Airflow ratings to 600 HP. Consists of a T3 turbine section, (standard, Stage II or Stage III trim) and a T4 compressor section (T04 trim).

The turbo offers the low inertia and fast boost response of the light weigt T3 Turbine wheel and the high airflow characteristics of the T4 compressor. Air flow rating of up to 600HP

3" Inlet Diameter : 2" outlet : Wet Floating Bearings : 1/8 NPT oil inlet

T3 Flange : Fits T3 and T3/T4 Manifolds

Specs: . 50 a/r compressor .63 a/r turbine .57 trim

Turbine wheel:

Exducer: 2.48"

Mayor : 2.89"

Compressor wheel :

Exducer: 2.07"

Mayor : 2.36"

40mmwsatebig.jpg

MonstA 40mm WASTE GATE 500HP $269 S/H$20

MonstA 40mm wastegates are external units constructed with die-cast mounting base structures and valve seats, sealed shafts, high temperature resistant diaphragms & utilize 40mm valves to support up to 500 horsepower turbo applications.

rb2025big.jpg

MonstA RB20 RB25 MANIFOLD $289 S/H$25

The RB20 RB25 MonstA Turbo Manifold is a direct bolt on to the stock turbo, or any after market turbo with a T3 Flange. Will fit Will fit RB20 turbo , RB25 turbo

Edited by cefiro69
Link to comment
https://www.sau.com.au/forums/topic/115617-check-this-out/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
    • So.....wire it up appropriately. You can't use the resister pack with those injectors anyway.
    • that’s the thing i’m on ID1050s and haltech not getting power due to the injector resistor 
    • ahh okay cheers, i was thinking of just going for the m073, think m079 would be way too overkill considering they are same size. 
    • My first car was a HG. I'm very familiar with them. A mild cam upgrade is a good idea. The 186 is a very flexible engine - meaning it has good torque from down low. You can give up a little torque down low for quite a lot more excitement in the mid range, and a bit more up top - but they are not exactly a rev monster. You need to upgrade valve springs at the minimum. For a bigger cam, you'd want to make sure it wasn't still running the original fibre cam gear. That would be unlikely, given that most of them shat themselves in the 70s and 80s, but still within the realms of possibility. Metal cam gear required. Carbies are a huge issue. The classic upgrade was always a Holley 350, which works, but is usually pretty bad for fuel consumption. The 186S had a 2 barrel Stromberg on it that was very similar to the one on the 253, and is a reasonable thing if you can find one, and find someone to help you get it set up (which is the same issue with setting up a 350 to work nice). The more classic upgrade was twin sidedraught CD type carbs, or triples of same, or triple Webers. The XU-1 triple Webers being the best example. You can still buy all this stuff new, I think, but it's a lot of coin to drop. And then the people able to set them up are getting fewer and further in between. There's still some, but it used to be everyone's** dad and uncle could do it. **Not everyone's! But a lot. All in all, I wouldn't get too carried away with the engine. Anything you do to it without a full rebuild for power and revs will only make it slightly faster. I am all in favour of a complete teardown rebuild, with nice rods and pistons, 10 or 10.5:1 compression, and a clean port job with at least a big enough cam to run 98 with that compression, if not bigger. And if I did that to a dirty old red motor, I'd want to inject it too, which I'd struggle to fight against the devil on my shoulder that would argue for ITBs and trumpets. But the bills would start to mount up, and it will still never make stupid power. OK, a few people still know how to build absolutely mental red motors, courtesy of the work that went into HQ racing and modern knowledge being applied. But even a 300HP red motor is no match for an RB20 with a TD06. So you have to decide what it's worth to you. I'd just put a set of 6>2>1 extractors, a 2.5" exhaust and an electronic ignition conversion/dizzy on it and just run the old girl like the fairly slow old girl that she really is.
×
×
  • Create New...