Jump to content
SAU Community

18" Lenso

Roy
 Share

Recommended Posts

Roy Grand Master

Roy

Posted
Posted

Lenso GT05 wheels

Size 18 x 8"

5 stud PCD 114.3 +35 offset so suitable for the usual R32/33/34/S14/S15/Z32 etc etc

Not very common, in fact i am still yet to see another car with these wheels. Have travelled about 1800kms and are near brand new, tyres have done a trip from Syd to Melb, and a return trip to Shepparton..so less then 2,000kms. Tyres are Falken 326, 225/35/18s

These rims were bought as they were a nice clean set of rims for the street. Selling as i have 2 1/2 sets of wheels, and hoping to use this money to buy some light weight front rims in the optimum offset for track work. Car is likely to have trouble getting re-registered so no longer concerned with spare sets of rims for the street.

Photos

(note Lenso rims on the front only...excuse the guards...i cant drive and thats why thr car is in the panel shop :( )

lenso.jpg

Better photos to follow

Asking $1450 ono

Link to comment
https://www.sau.com.au/forums/topic/116717-18-lenso/
Share on other sites
  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • Songo
      New kid on the block

      By Songo · Posted

      thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
×
×
  • Create New...