Jump to content
SAU Community

Recommended Posts

Ok guys just want to know how to change my fuel pump as I dont know how to dismantall bits and pieces surrounding to get to it . As I have pulled back seats out with no success and also taken off back shelf in boot with no success and undercar looks like best bet but dont know how.

Could someone pls help as I'm in need........

Thx In Advance

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/
Share on other sites

dont kno about r34s but on r32s the fuel pump is located in the boot, u just take off the plate an a few other screws and i comes out.

Nah the 34 is different I think as there is some sort of round thing in boot but cant seem to c fuel pump.

Pls Guys some help as car is ready to be tuned........ :O:)

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153044
Share on other sites

Yes you go through the boot.

It's on that shelf part on the drivers side.

There is a metal plate with 4 10mm bolts. Take that off then you will see the top of the tank.

Use a piece of wood and a hammer to get the round plastic cap thing off after you remove the hoses.

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153401
Share on other sites

Yes you go through the boot.

It's on that shelf part on the drivers side.

There is a metal plate with 4 10mm bolts. Take that off then you will see the top of the tank.

Use a piece of wood and a hammer to get the round plastic cap thing off after you remove the hoses.

I did that but dont know how to get the actual fuel pump out??????????

Is there a procedure for getting it out?

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2153877
Share on other sites

The stock fuel pump is mounted on a "gold" bracket... it is set at an angle into the fuel tank (about 45 degrees). Take your shirt off and reach down into the fuel tank you will be able to reach the pump easy.

From memory, the bracket just slides off it's holding plate with a firm tug - there are no bolts holding it in.

NOTE: Make sure you don't have any sparks or lights shining down there... don't want a fire starting now do ya?

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154046
Share on other sites

Which pump are you putting in... I hope you have a direct replacement otherwise you're in for a little surprise :ermm:

SHit Dont tell me that I have already have enough surprises!!!!!!!!

I am putting in a Bosch 040!

Does it slide up or something?

Pls tell that this will be ok :ermm::)

Edited by wrxxy
Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154132
Share on other sites

Thanks for that Bob...

Yes as my sidekick has mentioned it slides straight up...

The Bosch 040 sucks from the bottom of the pump, the stock pump utilizes a "sock" which reaches all the way to the bottom of the tank.

Now here's the choice you have to make;

1) Somehow fix the 040 to the bracket (I had to modify mine) and make a custom extension to the bottom of the tank - you will need a reducer made up and some thick silicon hose that goes to the bottom.

2) Extend the fuel hose and just drop the pump into the bottom of the tank. You may get some "noise" :ermm: But with a little bit of thought, you can get around this.

I went for Option 1) as it seemed like the better one to follow (at a cost of course).

If I was to do it again, I would get the Nismo or Tomei drop in's or use the stock pump and run it into an external pump + surge tank setup.

Cheers

S

Link to comment
https://www.sau.com.au/forums/topic/117099-r34-fuel-tank/#findComment-2154182
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...