Jump to content
SAU Community

Recommended Posts

Complete set of lightweight forged Volk SF challenge 18 x 8" and 18 x 9" rims +32/+35mm offset in 5x114.3mm PCD in silver/machined finish

both 8" fronts and one of the rears are in excellent condition. minimal gutter rash, no dings in the rim edge etc. unfortunately one of the 9" rear rims is damaged. It has not incurred an impact, but is wobbly for some reason, just progressively got worse with driving. May be repairable, may not be. Sold as is, ill leave it up to you to figure out whether it can be fixed and used again.

volks1.jpg

volks2.jpg

located in western sydney

pickup available, or delivery for the cost of return fuel available within 2 hours of sydney for a confirmed sale.

inspection and test fitting more than welcome, no tyres currently fitted though

$550 (!)

[email protected]

0409603238

cheers

ed

Edited by ed_ma61
Complete set of lightweight forged Volk SF challenge 18 x 8" and 18 x 9" rims +32/+35mm offset in 5x114.3mm PCD in silver/machined finish

both 8" fronts and one of the rears are in excellent condition. minimal gutter rash, no dings in the rim edge etc. unfortunately one of the 9" rear rims is damaged. It has not incurred an impact, but is wobbly for some reason, just progressively got worse with driving. May be repairable, may not be. Sold as is, ill leave it up to you to figure out whether it can be fixed and used again.

volks1.jpg

volks2.jpg

located in western sydney

pickup available, or delivery for the cost of return fuel available within 2 hours of sydney for a confirmed sale.

inspection and test fitting more than welcome, no tyres currently fitted though

$550 (!)

[email protected]

0409603238

cheers

ed

hey man can you send me pictures of the damage wheel to [email protected]

crack?? or just buckled front and back ?? spoke bent??

where you located?? liverpool area??

thankz mate

ho00ch

hey man can you send me pictures of the damage wheel to [email protected]

crack?? or just buckled front and back ?? spoke bent??

where you located?? liverpool area??

thankz mate

ho00ch

hey mate, i can send pics tomorrow evening of the questionable wheel... but to be honest, theres actually nothing to see physically wrong with it (ie no cracks, flat spots, bent spokes etc), its just got a bad vibration when you drive it.

heres a blurry pic of the two back wheels taken the other night. the dud one is the one to the left - i wrote on it with yellow crayon which you can just see. the one on the right is fine

WheelsImage00003.jpg

but yeah, like i said - will happily take proper pics tomorrow night

cheers

ed

oh - and located in penrith :rofl:

Edited by ed_ma61

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...