Jump to content
SAU Community

Recommended Posts

Changed oil in my S2 2nite. I disconnected plug at crank angle sensor?, on front of ex. cam, 2 turn eng. over 2 get oil pressure up. Connected plug, started and noticed 'eng light on dash'. Turned car off, restarted, stilled stayed on. Never noticed it staying on b4. Any ideas please. :P

Link to comment
https://www.sau.com.au/forums/topic/118978-engine-light-on-dash/
Share on other sites

Changed oil in my S2 2nite. I disconnected plug at crank angle sensor?, on front of ex. cam, 2 turn eng. over 2 get oil pressure up. Connected plug, started and noticed 'eng light on dash'. Turned car off, restarted, stilled stayed on. Never noticed it staying on b4. Any ideas please. :P

*tip* when u change your oil u dont need to turn the engine over to get pressure. maybe try reseting the ecu???

sorry dude im not much help :)

I also put on a new filter which was empty, so I don't like starting an engine without getting oil pressure up first. Wife took it 2 Nissan 2day, they put the 'consult' on it, they reset it. Light was on because I unplugged wire.

I also put on a new filter which was empty, so I don't like starting an engine without getting oil pressure up first. Wife took it 2 Nissan 2day, they put the 'consult' on it, they reset it. Light was on because I unplugged wire.

hey mate if u install a new filter just fill the filter before u install it and it will be 99% full. i was told by plenty of people including sydneykid that on a brand new rebuilt engine (thats never run) u dont even need to crank it round to get pressure, he said just start it and it will build pressure straight away.

just my 2c worth :D

cheers

Cruise,You must be a magician lol. I haven't been able 2 fill an oil filter then tip it on its side to screw on2 the side of a motor without oil running out and making a bloody mess. As it was i had 2 degease after removing old filter. Cheers

Cruise,You must be a magician lol. I haven't been able 2 fill an oil filter then tip it on its side to screw on2 the side of a motor without oil running out and making a bloody mess. As it was i had 2 degease after removing old filter. Cheers

gtr's r not fun with the front diff in the way, but thats y u get a remote filter setup and i can do it without spilling a drip :ermm: u gotta screw the filter on bloody quick to avoid abit of mess without the relocation kit :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
    • Hello everyone, I am happy to join you.
    • Whereabouts are you, that looks exactly like Akira's old car....
×
×
  • Create New...