Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

No motor is still original and strong. Great compression tests, also becausevspec r32's came with the steel turbines in the turbos, there are no leaks at all.

Had them looked at last month.

Car has only driven about 400 kms in 18 months.

bump

mate you were going good until the stupid post of bump and then the price drop.You cheapened yourself and your car.Everyone does it and its so irritating.First the spill about how you dont want to sell it,then how rare and collectable it is,then the price,then the price drop.Its just so predictable.Leave it at 38k or just write the real price you want.Now all the forum users will wait untill next week and see your next price drop and so on and so on.Thats why the ass is dropping out of the price of them.No one has the guts to name there price and wait or be patient.Ive read guys here asking 32k for gtrs and a week later its 26k.Just so stupid.We can all see it coming from the minute it goes up for sale. :dry:

Paul - For a $2000 loss, it brings it into the reach of more people, like me. What i hate is people saying "i want to sell this car" and then not budge on the price. It goes both ways. And it's up to the seller.

I need to save a bit more, but if it's still around in a few weeks, i'll be looking at it very seriously.

Will not drop the price below $36K. Have had some interest, but no genuine buyers. I can wait. Car is being advertised in Unique cars next month. If I dont sell it hear, it will sell.

NOW THATS MORE LIKE IT.BEST OF LUCK.

No motor is still original and strong. Great compression tests, also becausevspec r32's came with the steel turbines in the turbos, there are no leaks at all.

Had them looked at last month.

Car has only driven about 400 kms in 18 months.

No interest in buying (I already have enough Skylines) but just to clarify for possible buyers who may be misled. V-specs never in any model had steel turbine wheels, but have ceramic turbines, and are therefore just as likely to fail without notice as non V-spec. N1's in 32 and 33 have steel wheels and 34 N1's have Inconel turbines and ball bearing centres. That said, good luck with the sale

Nick, this is not about discussion but false advertisement. Anyone who has been on here a while knows only N1 turbos have steel or inconel turbines as stock fitment. There is no difference between standard and V-spec turbos on the different models.

Enjoy your reading KBNR32.

http://www.skylinesaustralia.com/forums/in...GTR*+R32*++N1**

http://www.skylinesaustralia.com/forums/in...GTR*+R32*++N1**

http://www.skylinesaustralia.com/forums/in...topic=71939&hl=

So you are quoting yourself. All correct except the turbos mate. Again, good luck on the sale but be honest on the turbos.

http://members.dodo.com.au/paul/docs/discu...n1-vs-stock.txt

Maybe you can post the turbo part numbers.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...