Jump to content
SAU Community

Te37 Volk Racing Ray's Engineering

Sky_nismo
 Share

Recommended Posts

Sky_nismo Rising Star

Sky_nismo

Posted
Posted

Genuine RAY'S Engineering Volk Racing 17inch

17 by 8.5 offset 30 fronts and 17 by 9.5 rear offset 35

These wheels are in great condition.

These wheels are hard to come by as well hardly you can find a set that’s 8.5 and 9.5 wide

Also comes with Advan tires worn

Item Condition:Only 2 Wheels has curb gutter

Location: CBD Melbourne

PRICE $1550 pick up

Will post interstate at buyers cost.

Email me if you want more image.

Email me at: [email protected] if you have any inquiries.

Thanks

post-3757-1150799526.jpg

post-3757-1150799540.jpg

post-3757-1150799556.jpg

post-3757-1150799575.jpg

post-3757-1150799589.jpg

Link to comment
https://www.sau.com.au/forums/topic/123030-te37-volk-racing-rays-engineering/
Share on other sites
alex1991s Collaborator

alex1991s

Posted
Posted

Hey need wheels for 34GT. Would you consider $1450 without the suspension. The suspension wouldnt fit into the R34 GT would it?

Im located in Camberwell. Im on my sons account, sorry. Can you PM back. What car were they on before?

Sky_nismo Rising Star

Sky_nismo

Posted
  • Author
Posted
Hey need wheels for 34GT. Would you consider $1450 without the suspension. The suspension wouldnt fit into the R34 GT would it?

Im located in Camberwell. Im on my sons account, sorry. Can you PM back. What car were they on before?

Bump

  • 3 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      About $4k brand new, available from vendors in Oz, or via an importer from Japan. Although that is for an R34 box, so you also need to buy the push clutch front plate (brand new from Nissan) and swap that over, and drill the bellhousing for a push clutch slave cylinder.
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Bennym35
      New guy

      By Bennym35 · Posted

      Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • Songo
      New kid on the block

      By Songo · Posted

      thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
×
×
  • Create New...