Jump to content
SAU Community

Recommended Posts

heyyy guys

Got this little issue with the power output.

Car has been running fine till now

when car first turned on it idles at about 1100 then drops to about 500, used to idle at 1000 - 11000

sound from exhaust is like its riding fine then it drops a lil and picks up like its missing something.

Slow pick up on the revs when acc pressed, looking near the alternator section it sounds like its making a whinding noise, battery was replaced 4 months ago..........

car is 7000ks ova service schedule

(getting done this weekend)

anyone got any ideas ????

any help would b good :D;)

thanks

Edited by JUN`R32
Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/
Share on other sites

I thought that was pretty normal? Isn't it the cold idle control? Some little piece of metal that bends as it heats up apparently.

Still, have a search for "idle" or "cold start", because it sounds like a bunch of questions that have been asked before.

The whirring noise is probably your alternator or a belt... mine makes an induction kind of noise, but it's just normal belt sounds. As far as the accelerator pickup... are you saying that there is lag when you push the pedal, or that the revs climb too slowly when you jab the pedal? That could indicate an air leak.

I'm no expert, but if your car is well and truely due for the 100,000kms service, you could have something more severe if all these things started happening at the same time. A stuck idle bearing or pulley would make a lot of noise and also hold the revs back.

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2297450
Share on other sites

But if he pushes the pedal down, the revs move too slowly... there has to be something amiss there! It's still a cable throttle-body, so when that is open, it should be drawing in plenty of air.

I guess even an air leak shouldn't cause that, otherwise it'd idle really poorly. Maybe a blockage or something more technical.

I'm at a loss really.

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2298955
Share on other sites

A seized aircon, or water pump? Something is holding it back it seems... if the timing belt is rubbing against a seized idler or tensioner bearing, you won't have a timing belt for much longer.

Get your mechanic to check it out while he's servicing it mate.

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2298962
Share on other sites

yehh i will have to get him too

thanks for the info

one more thing,

wen revving the engine to about 3 or 4 then releasing the acc the revs drop down to almost a stall, and pick back up slowly :S :S

when lights are turned of the engine revs rise a little,

battery has been changed for just a regular battery from kmart as it died 4 months ago, same power output though

anyone reckon this might be an issue aswell ??????????????

thanks heaps guys

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2299398
Share on other sites

Do you have a BOV that vents to atmosphere? That can cause the car to actually stall when doing what you are doing... but then I think an air-leak could do that too. I also think that an air-leak could give you the slow revs. If not an air-leak, then some kind of bockage... either way it sounds like there's not enough air getting into the plenum/cyclinders etc. That's a novice guess, but i'm keen to hear what the problem turns out to be!

Don't buy batteries from Kmart and the likes.. they have probably been sitting on the shelf for 6 months or more. Best to get (at minimum) a Century heavy duty battery from a service station or better yet, from a reputable mechanic or auto electrician, as they turn over their stock much more frequently.

By heavy duty, I mean 11-plate, 400cca or more. You can go nuts on batteries, but unless you're running all sorts of flashy lights and multiple amps and subs, you won't need it. I run a 330cca 11-plate and one amp to drive my 4 speakers. No dramas with the stereo on for many hours while cleaning without flattening the battery.

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2299826
Share on other sites

i got the oil and oil filter changed, as i didnt have time to do it myself, got car back on sunday

and it works fine, the revs go up and idles at 700 nicely, still need to change sparkies though

thanks for the info randy

will get myself a new battery aswell

cheers,

Link to comment
https://www.sau.com.au/forums/topic/124304-power-issue/#findComment-2303516
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...