Jump to content
SAU Community

Sold

_Wing_
 Share

Recommended Posts

_Wing_ Proficient

_Wing_

Posted
  • Author
Posted

these seats and rails were originally out of a fresh import gtr32 - the owner was quite big and didn't fit. For my s15 (and all silvias/180s), one mounting point was approx. 3cm too short so that bracket was cut off and a new plate welded on by a professional. To have this fit skylines again all you need to do is drill a hole approx. 3cm in, no welding required.

the seats have no branding - choosen because i didn't want to have a big bride/sparco/recaro logo that say "steal me!"

the harnesses can fit with no modifications; if you want to run with the optional 5th and 6th point (that go around your crotch area) then you will need to find a mounting point below the seat.

:)

Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2319745
Share on other sites
satanic Grand Master

satanic

Posted
Posted

Any chance of getting some more photos of the seats (front, side and back) in full detail?

Also, I have a coupe; how is this going to affect people climbing into the back as they're fixed buckets

Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2319754
Share on other sites
  • 1 month later...
_Wing_ Proficient

_Wing_

Posted
  • Author
Posted (edited)

i will sell the drivers side seperately:

drivers side bucket + rail = $550

1 x 3" harness = $250

together = $750

IIRC the A31 rails are the same as R32/33/34 rails, so if i do remmeber correctly the rails will fit your A31 :(

Edited by _Wing_
Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2447004
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Predator1
      Tomei gasket

      By Predator1 · Posted

      Didnt realise RB's had more then 1 head.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • Kinkstaah
      Unpeeling the Orange

      By Kinkstaah · Posted

      The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...