Jump to content
SAU Community

Recommended Posts

I know this is a skyline appreciation forum but i have always been open minded about cars. If the XR6t had been around when i bought my GTS25t i would have had a much more difficult time deciding on buying my skyline.

In the following link they say that with a couple of tweaks and some extra boost you get 252rwkw out of the XR6t. How tuff is that. Also they say that 300rwkw would be a "doddle", that will really put the wind up someone driving a HSV with 300 flywheel kw.....

http://www.fordforums.com/showthread.php?t...25&pagenumber=1

I think it is impressive that a local manufacturer has finally come up with a MODERN performance car. None of this single cam push rod junk but a really serious peice of gear. Mind you dont get me started on how the intercooler is plumbed because that really was a MAJOR COMPROMISE.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/
Share on other sites

bolting on a turbo doesn't instantly makes it a well refine sportcar as a skyline. but it does help the falcon street cred though. if u get a chance hurl one into a sweeper at the same rate as u would do in a skyline and see how much room there is left in ur undies. It's still a family car in the end.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230877
Share on other sites

Hungry 6 have you tried driving one????

It is more of a family car than a race car (skyline being a race car of course) as such it will weigh more.

I personally hate the way the intercooler/ inlet manifold/ turbo is piped because it is a compromise. BUT you cant argue with a family car that pulls 240kW running 6psi which is heavily detuned. Oh by the way can your car seat 4 people as comfortably as a XR6t???

I took one for a run and i was surprised at how the suspension combined with the traction control made the car stick under serious accelaration through some cornering. The sales person did get a bit edgy at times but i assured him that i was looking at upgrading from the GTS25t to a family car with some go (cough cough like hell i was).

They didnt JUST bolt on a turbo if you check the specs they also dropped the static compression ratio and did a lot of heat shielding among other things.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-230969
Share on other sites

My mate works for the company that makes Ford's transmissions, and agrees the manual is at an end for torque handling, they have been leaning on it for years and keep asking to do what it was never designed to do, with this in mind the 5 spod doesnt do that bad a job.

He has worked primarily on the auto, and with him having driven my 32 GTST many times when im pissed and egging him on, he has a good idea what my car can do.

For the record the guy isnt full of BS, and claims despite the weight of the car, and saloon heritage, the development mules that he R & D flog my GTSt in accelaration, have great brakes, and handle great. He says with the handling you just have to be mindful the it is a production car with a pretty hefty kerb weight, so no brakes/heavy acceleration mid corner/ebtry to corner etc, be smooth and it can do the job. Hell he has driven the thing on great ocean road.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231153
Share on other sites

I've heard from a few sources that the XR6t has a boost limit of 7psi.

Once it hit's 7psi the ECU starts to pull back timing and then starts the boost cut - just like some R33 gts-t's hit at 12psi.

If this is true, it'd be a pain in the butt to go to a full ECU change on such a modern car for a few extra psi :D

They are nice cars though. Boss at work has a blue one... Nice......

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-231353
Share on other sites

There was a good article in the last HPI comparing the XR6 Turbo to the Supra. They said "The closest thing to a Japanese car to come out of Australia. We can't praise the XR6T any more than that".

I think the guy doing the review was a little biased as he owns a Supra, but hey, what can you do?

The writer goes on about how the 2JZ-GTE is the greatest and most proven engine of all time, whereas the 240T still has to prove it's self. "The few players in the aftermarket who have tested the 240T engine have come away confused and frustrated with an uncooperative managment system, and intercooler/exhaust systems that are far from optimum".

Apparently the LPG spec rods are a must for a serious build-up.

They also said that the Ford doesn't like to be revved!

All in all though, I think Ford is onto a good thing. However, if I was looking for a sporty family car, I'd still by a WRX!

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232077
Share on other sites

OK

Firstly it is a 4ltr. Motors with large swept capacity dont need to rev much because the have bulk torque early on in the rev range where as my RB25DET needs to be revved to get any go out of it.

For a sporty family car i would think it is ideal because you get a large turbo six with auto. You can be as lazy as you want to be and you can seat 4 passengers with large arses comfortably.

Link to comment
https://www.sau.com.au/forums/topic/12619-ford-xr6t/#findComment-232092
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...