Jump to content
SAU Community

Recommended Posts

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

car could easily run high 11's.. was running low 12's but that is on some crappy rubber and very shit launches.. only been out there once..

with semi slicks and the right launch, it could easily get into 11's

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2396444
Share on other sites

yeah it is at the wheels.. yeah dyno sheets i will show you.. it was tuned by unigroup so they well i think are the best tuners in sydney, and tuned it safely.. will scan dyno sheet in for you

been holding up perfectly fine for 8 months no hiccups or anything..

the blocks are solid

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2402993
Share on other sites

$200 Spotters fee for whoever refers the car to friends and they go through with the sale.

This is free cash for whoever refers their friends to buy their car.

So go on tell your freinds and get 200 bucks for free if they buy the car

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2414010
Share on other sites

peak of 1.2 bar which is 17 psi. So it normally sits at 1.2 - 1.3 bar to get that much power, with the hi flow turbos they are all not the same, so Unigroup have told me that i have got one which is pulling more punch since they have tuned it safely and reduced the power just in case, but it could easily go to 270rkw they say.

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2414648
Share on other sites

  • 2 weeks later...

Keeper: splitfires does the job so well

and i recapped the plugs it .69 but that is all

splitfire helped so much..

dazz: side skirts came with car when my mate purchased these ages ago, so i assume these come from japan

:)

Link to comment
https://www.sau.com.au/forums/topic/127054-sold/page/2/#findComment-2462410
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...