Jump to content
SAU Community

Recommended Posts

Hi Guys,

Just hoping someone can point me in the right direction.

I've got a 96 R33 GTST with K&N Pod, 3" Zorst, BOV and FMIC with boost around 11-12psi (done by a Turbosmart manual bleeder value).

When i go to accelerate (overtaking on the highway) you can hear the pod filter etc going crazy sucking in air but the car doesnt really take off (it used too and it isnt just that i'm used to the car.. i've had it for 2 years and i know somethings wrong). It will take off but struggles and it surges and then hits flat spots and then surges again all the way up the rev range. Seems like something is holding it back.

I do have dud coils but i have taped them with electrical tape and they seem to be ok for a $10 fix (they are really bad without taping).

I have cleaned my AFM once before when i had a very similiar situation and it seemed to have resolved the problem but i dont want to keep getting this problem. I've only driven the car about 2000kms in the last 6mths (also since i cleaned and re-oiled the filter).

Also when travelling on the highway and going to over take (whether in 4th or 5th gear), if i just hammer it, my car cuts out (like the fuel-cut comming in) but if i slowly climb there is no cut out.

If anyone can suggest where i should look at, i'd appreciate. thanks

well the cut out in 5th gear is rich and retard mode. only way to get rid of that is either new ecu or wind the boost down.

how old are your spark plugs? and what type? that could be part of the problem.

Hi,

Thanks for the replies.. Just wondering why when i overtake i 4th or 5th and i slowly put the pedal down it doesnt cut out but when i plant it, the fuel cut comes in... could this be because of a bad bleeder/boost value?

Also, i havent changed my sparkies in a while so maybe i will this weekend and i'll gap them.

Anyways, thanks guys again.

wouldnt think the boost controller would have anything to do with the problem. It will just be fuel cut coming in...R&R as stated before, a/m ecu will fix it. Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change.

Yer im in a similar situation dude, with the same b/c as urself.....try winding it back a touch....

Originally posted by r33 racer

Generally winter will bring upon boost spikes and induce R&R more so if you have the boost set right on that threshold and the occassional squirt mixed with colder climate will bring upon that change

Exactly wat i thought! :laugh:

the way that r&r works isn't by boost pressure. it isn't just a case of once it reaches a certain pressure it cuts out. that is why it won't do it if you ease the throttle on.

but yes the cold weather has an effect on it. just wind the boost down a bit.

its based on a ramp scale. i started a thread about this to find out exactly.

what happens is that the ecu has a set maximum airflow per rpm. so if it exceeds that amount it cuts out.

for example, the airflow at 14psi might be within limits at 6000rpm, but not at 3000rpm, so it cuts out. i will draw a graph to illustrate it when i get time.

haha no...i dont think so...try winding the boost down and see how it goes mate. Take things one step at a time...you never do 5 things to fix one problem or you will never know what fixed it.

Thats also an idea below...try some contact cleaner through your afm.

Edited by r33_racer

I didnt notice this problem until last weekend when i went for a long drive and needed to overtake. But the period after re-oiling, i didnt have any problems.

And yes i would love to buy new coil packs but i dont have the money yet.

Well, i'll wind the boost down first and get new sparkies and have em gapped.

Then i'll see how it goes.. I'll clean the AFM anyway.

Thanks guys.. will keep you posted.

Could be a number of things (as usual) but coil packs usually fluctuate when faulty under load which is what you are experiencing when trying to overtake. Which also explains, that when you decrease the amount of boost you are running that the problem will go away.

Theres plenty of advice throughout these forums to detect faulty coil packs.

Hi All,

I've changed my plugs with NGK BCPR6ES (i think that's it) which are standard gapped to 0.8mm and wound down the boost to run 10 or 10.5 (needle on boost gauge is half between 10 and 11). The 33 seems to run quite well.

However saying that, the old plugs didnt look to bad either but who cares when the car is running much better.

thanks alot.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not really, but the heater box is pretty simple mechanically....if the door is one way the air bypasses the heater core and if it is the other way it goes through it for warm air.  If you are sure the actuator you moved manually is for the heater mix (there would also be one for output air direction) then I'd take the heater box out and see what is happening (you'll have to regass and re-coolant the systems afterwards) BTW pp724 onwards from the GTR workshop manual cover the system in good detail, it is probably worth checking. I think the IAT sensor might be a problem electrically for getting cold (if you got 24 error code not -24 it thinks the incoming air is -50c) and it covers how to test the sensor (although most likely it is either not plugged in or a wire is damaged)
    • Use the GKTech subframe bush and bring your subframe 10mm closer to the chassis. You'll need to fix an exhaust hanger to suit. One of the best mods I've done.
    • You'd really have to pull it apart further to know, it least you can be confident that the one heading to the back is not connected any more. There was once a ground on the shifter seal mount too, your head unit issue could be that simple
    • Perfect, I'll get to it this winter then at the same time as I weld on my anti squat kit. 
    • Alright so my 32 only has one temperature no matter what degree you set it to. I’ve tried disconnecting the servo motor arm and moving it either direction and got no change. I’ve fixed the leak in my AC and re charged it and with it on and clutch engaged it still blows hot even though the low pressure pipe going to the firewall is ice cold. Both heater core hoses are hot while running as well. Diagnostic code showed 24 for intake air temperature sensor. Anybody got any ideas?
×
×
  • Create New...