Jump to content
SAU Community

Recommended Posts

  Terminal said:
i have my auto one out of the car and my manual one sitting around, i'll take a few shots and post them up here tonight.

Oh yeah, I forgot about that - guess I don't have to worry about it then, hey?!?!

Alright, i got the handbrake installed. the handbrake i got was from an R33 GTR and one of the brackets was at the wrong angle. luckily, working on a construction site, oxy torches are quite abundant, so a quick blast and bang with a hammer sorted it out.

it still wasn't 100%, but served it's purpose. i used about half a dozen washers underneath to get the correct height and angle from the handbrake:

post-4352-1154698079.jpg

now i just have to adjust the tension on the cable and i'm all set. hope this helps people. i'll update with the console pieces tomorrow and then try to install it. i don't know how it will go around an auto shifter being there still, but we'll see. it's a bit of an incentive to get the rest of it in i guess.

Here are some pictures of the manual and auto consoles compared:

post-4352-1154780682.jpg

from this picture you can see the manual console (on the left) is slightly longer than the auto one. it also has a spot for 2 more cup holders (which i haven't installed because the atessa computer is still in the way)

the manual is also slightly lower than the auto. this means the pocket in the console is quite a bit shallower:

post-4352-1154780922.jpg post-4352-1154780975.jpg

the gearstick surround is also a different length, not including a recess for all sorts of knicks and knacks:

post-4352-1154781122.jpg

so there you have it, the manual vs auto console comparison. sorry about the picture quality, but it's easier with my phone than getting the camera out. supposed to be 2Mpixel, but it doesn't look it.

  R33stagea said:
ive got one being moulded up in 2 weeks.

much cheaper than a nissan one,and saves changing alot of parts.

bracket or console?

the whole manual gearbox in a series one is starting to look more and more expensive every time i look at it

  Terminal said:
Here are some pictures of the manual and auto consoles compared:

sorry to bother

is the manual console from a S1 stagea manual?

or is the console from a different series?

  Terminal said:
only the series 2 came with a manual option, oh and the 260RS. it's the series 2 manual console

deluxe.

is the only modification required to the console is the relocation of the ATESSA unit?

  Terminal said:
no, you need to remove a bracket that holds a mount for the auto console that isn't part of the manual console. it's got 3 spot welds, you just drill them out.

thanks, im very very close to buying a Rs4 and GTR box straight after, might look at getting the parts shipped over from NZ in the likes of the console etc, if you pay someone there to buy the parts, then they delcare them as motor spares for personal use and mark them around $150 a shipment the duty and taxes should be negligable

when doy ou think you will have photos of the console in the car?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...