Jump to content
SAU Community

Recommended Posts

I might be able to get a limited quantity of Bosch 044 or 984 fuel pumps. Not sure on final pricing yet but they should be around $350 for the 044 and around $250 for the 984. I was originally going to get the 984, but since it's so cheap to get the 044 I'm tending towards that instead now.

Anyway I was just wondering if there would be anyone interested in these at this price. If so please reply here. Please note that this is going to be a one-off! Once I have my pump that's it. The only reason I'm posting it here is because I may be able to order several at once, but they will more than likely have to be the same type. So tell me (in public please, no pm's because it becomes difficult to maintain a tally) which pump you want, and I'll probably get whatever the majority wants (but if there's not much in it, I'll go for the 044).

The reason why it's a one-off is because I have a friend who deals with Bosch but not in their car parts, and Bosch don't like trading to non-auto dealers with their car parts. This is going to be a personal favour to my mate from his contact in Bosch and it won't be repeated! Escpecially since it's also a personal favour to me from him :P

It's also entirely possible for the above reason that he can only get one (for me) so please don't get offended if this offer is suddenly withdrawn. I'm only offering this to fellow enthusiasts of this forum on the off-chance I can get more than one.

Link to comment
https://www.sau.com.au/forums/topic/12916-bosch-044-or-984-fuel-pumps/
Share on other sites

Originally posted by dabigbolf

what are the part numbers on the bosch 044's?

The last 3 digits are what everyone refers to them as. The complete part numbers are as follows:

0580254 044

0580254 984

Sorry guys, just got word that I can get one only direct from Bosch :D (for me, and a lot cheaper than I thought :)) However, I still may be able to help.

Firstly, the trade price for the 044 from Repco is $355, and for the 984 it's $245. So if you can, try getting finding someone who can get trade prices from Repco and all will be sweet. Or even if you work for a company that's even semi-vaguely automotive-related you should be able to fax through an order on your employer's behalf and probably get trade prices that way.

Secondly, my mate may be able to deal with Repco because his company may fall into the aforementioned category, but this would be a bit of a hassle and he'd probably want about $20 per unit for his time. So the theoretical price would be a bit more than I originally quoted, ie around $375 for the 044 and $255 for the 984.

The upside to this is if he *can* do this through Repco, there will be no time limit or rush of orders needed. I should find out by Monday if he can set up an account with Repco and get the trade prices for you. But if you can deal with Repco yourself then that'll be better, it'll save some hassles and 20 bucks.

Hope this has been helpful, and sorry about the original offer falling through! (it would have been a LOT cheaper than what I first quoted too :))

Edit: Crap! It just gets (slightly) worse and worse! I forgot about the freight cost from Repco to my mate's work, and from there to you. Dunno what that would be but it would be added to the cost. Dealing with Repco youself is definitely going to be the best way if you can swing it but even at an extra $30-40 or so it's still going to be much cheaper than retail.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...