Jump to content
SAU Community

Recommended Posts

1990 model Nissan Gtr 2pac BLACK

DRIVELINE:

Brand new Extream Super Heaveyduty 5 puk clutch (still had original nissan clutch in it)

Full re-genuine gasket set TwinTurbo side after turbo inspection

Full Redline Fluid system

Full Service history Since import

Nismo 320km Instument panel

HKS Adjustable Coil overs

HKS POD'S

Uppgraded ECU (japan)revised AFR no limiter.

Brand new Natrad Radiator

Autometer Boostguage 35psi

Climate Control Calibrated ( a must for Black car )

3inch Exhaust

Recalibrated Oilpressure Sender

COSMETIC :

Brandnew 2pac Black paint

brand new Original Carbra (black) used once

Tinting 23%

Original skyline floor mat's

Hiqual lined water proof car cover

Never been in Accident :devil: as far as detailed inspections can tell and been Inspected with a fine tooh comb as far as driveline

It has 145000kms on nismo instrument cluster

Car runs a nice 210 kilowatts on 12psi and very tight alround.

I dont really want to sell it as it took me so so long to hunt down this cleaner Example but realestate has come up

$20800 OnO

DSC01040.jpgDSC01041.jpg

DSC01039.jpgDSC01038.jpg

DSC01047.jpgDSC01045.jpg

DSC01043.jpg

Image021-1.jpg

pls note that this graph was taken with a small rear turbo gasket leak as well as an original nissan slipping clutch. All has been replaced and it runs alot better than when that was taken.

Extra's Bought for the Car, theses are not included in price and would be negotiated / sold on top of asking price.

the Motec m8 was to be its Controll and Guage stystem for Boost , Nos , Traction ,Launch Control all running from a dedicated laptop hence why the car is not all Auxiliaried out!

Motec M8 808 version Fully optioned for Track Racing (includes Logging , Traction Control, Boost ,n2o Gearcut etc $2200 will only be sold with the car !!!

Brand new Turbosmart 48mm Wastegate $650

Edited by ishh
Link to comment
https://www.sau.com.au/forums/topic/129334-r32-gtr-black/
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

thank's guy's

All I can say is it is the neatest one i could find and really happy with it after sorting certain small shall we say, Japenese bug's out :)

I am fairly Astonished that no one has sussed this car with its motec availability!!! $22000 for a Black A1 track enabled MOTEC ECU Godzilla...

i forgot to mention it has its own custom waterproof Car cover tooooo ;)

Edited by ishh
Link to comment
https://www.sau.com.au/forums/topic/129334-r32-gtr-black/#findComment-2496616
Share on other sites

NO jeep thanks .. I got a nissan patrol now for the mud :)

My self i cant tell if the water pump has been changed and i aint taking all the stuff off to find out because it's running fantastic. I believe the timing belt would have been done at its 100,000 magor service... Some one here will know what's involved with that service as i havent studied what nissan actualy do for the 100,000 .

Link to comment
https://www.sau.com.au/forums/topic/129334-r32-gtr-black/#findComment-2523339
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...