Jump to content
SAU Community

Recommended Posts

- Original GTR32 Strut tower brace

(Black ends with silver centre bar excellent cond.)

Make an offer!

- Original GTR32 floor mats (in good condition)

Make an offer!

-Apexi twin pod filters (done 2,000ks if that! as new)

$325 ono

-VOLK RACING 18" rims (AS NEW, silver with polished writing

$2,500 no tyres

- 3" mild steel cat back exhaust (super cat stainless muffler)

$450 ono

- HKS type 1 TURBO TIMER (has 0-100 timer etc includes harness)

$300 ono

- 3" cat pipe

$50.00 or case of beer :uh-huh:

PM me...

I might be interested in a few parts.

Will the strut tower fit if I have aftermarket (Tein) suspension?

Do the pods have the adaptors to fit an R32 GTR?

And does the turbo timer have the wiring harness/adaptor for R32 GTR? And also does this turbo timer remove the speed limiter??

thanks,

Andrew

Will the strut tower fit if I have aftermarket (Tein) suspension?

YES

Do the pods have the adaptors to fit an R32 GTR?

YES, FULL KIT + INS

And does the turbo timer have the wiring harness/adaptor for R32 GTR?

YES

And also does this turbo timer remove the speed limiter??

NO and I don't know of ANY that do!?

All the bits just came off my 32GTR before I traded it!

Originally posted by GTRKING

Will the strut tower fit if I have aftermarket (Tein) suspension?

YES

Do the pods have the adaptors to fit an R32 GTR?

YES, FULL KIT + INS

And does the turbo timer have the wiring harness/adaptor for R32 GTR?

YES

And also does this turbo timer remove the speed limiter??

NO and I don't know of ANY that do!?

All the bits just came off my 32GTR before I traded it!

Thanks for that mate.

Im more interested in the turbo timer than the other parts.

I think there is 1 turbo timer that does remove the speed limiter, a blitz one i think from memory???

Anyway Ill get back to you real soon about the turbo timer (if its still for sale)

thanks,

Andrew

I saw the picture after I posted. Just stupid and lazy on my part.

I'll give you $100 plus shipping, direct deposited into your account before you ship.

you can call me or email me if you like

[email protected]

0411 471 684

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...