Jump to content
SAU Community

Recommended Posts

Hey i need to fix my fuel sender in a r33 S1 4door turbo . and im a bit worried in doing it my selfh since im not familer with cars and saving to move out dont want to pay a mechanic 300 just to fix it i know how to do it in my head i mesmerised it in my head butttt it might go boom and i want to live ive had the car for 5 months now and it has been like that from the get go and i need to resolder my wires in my drivers side door as well for the power windows could do that my selfh easy after reading about it so if any one in the area can help out a fool with the fule sender will be greatley appreciated.

and i know no one else that owns a skyline all my friend want one but dont have enough money

i live in vic 4 km from the city western suburbs will drive any where for some help

Link to comment
https://www.sau.com.au/forums/topic/133399-any-one-in-the-area/
Share on other sites

im talking about the access through the boot. there is a panel with 4 bolts holding it in, next to your battery in the boot.

i recommend you wait till your tank is almost empty before you do this.

1. take the panel off

2. disconnect the looms (leave the hoses running from the lid because fuel will rush out of it. watch out you dont damage any when loosening the cap).

3. get a plank of wood or a long screw driver and hammer then hold it onto the little little fin things on the cap, then hammer it around to loosen (let me know if this needs to be explained a bit better). watch out for the rubber seal around the lid.

4. detach the fuel lines and remember where each one goes. the reason i left the hoses for this stage is when the fuel starts rushing out you'll be able to let it flow back into the fuel tank.

5. grab the level sender and mount the sucker back on.

6. when putting the lid back on, i recommend using a bit of WD40 to get the lid and the rubber seal sitting snug inside where the cap goes on. you'll know what i mean when you see it.

7. put the rest on in the reverse order and it should be right smile.gif

i just copy and past what u have to do hope that helps and im free on weekends

Edited by R33sedanturbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...