Jump to content
SAU Community

Carbon Fibre Vented Bonnet

danoz

By danoz,
in Four Door Family & Wagoneers

 Share

Recommended Posts

D-limo Veteran

D-limo

Posted
Posted

yeah.. It's in the latest HPI if you didn't already know.. Can't say I remember seeing a Cefiro specific carbon bonnet around.. Fibreglass vent will do a simular job for a fraction of the price of sourcing a cf one.. My stocker bonnet is surprisingly light with some of the bracing removed too.

danoz Collaborator

danoz

Posted
  • Author
Posted
yeah.. It's in the latest HPI if you didn't already know.. Can't say I remember seeing a Cefiro specific carbon bonnet around.. Fibreglass vent will do a simular job for a fraction of the price of sourcing a cf one.. My stocker bonnet is surprisingly light with some of the bracing removed too.

cheers man yer just got the magazine today it the first good pics ive seen of the car as it is in brissy and im in perth that was done b4 this dodgy place that fitted the apexi pfc and avcr to my car blew it up... so now about and 30g has gone into it and another 20g to go haha... motor is all forged cp piston revi rods r33 crank acl race bearings tomei sump and cam baffels tomei 260 pon cams and cam gears n1 water pump n1 oil pump twin hks 25/30s and so on and so on

D-limo Veteran

D-limo

Posted
Posted (edited)

Here you go bud

http://cgi.ebay.com.au/Nissan-Cefiro-D1-St...1QQcmdZViewItem

Color matched fibreglass would look phat too.. Maybe find if any fibreglass sheets are used in the carbon one.. Sometimes only a layer or two of carbon on the top is used.

Also what are the specs of your rims?

Edited by Drift_Limo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • GTSBoy
      Wheel Sizes & Offsets For Skylines

      By GTSBoy · Posted

      There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • GTSBoy
      Rear Sway Bar Busshings - Holden Astra TS (2002)

      By GTSBoy · Posted

      I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...