Jump to content
SAU Community

Recommended Posts

So I'm getting an Rb25 conversion, so once they take tne engine out, they will dump it or something.

The engine is still in the car, so if you want it. get it off yourself or give me heads up to get it off. I have everthing including the ECU, Reco head not been used yet but is on.

Ive got a 2 1/2" mandrel bent exhaust to suit RB20DE and fits a 91 onwards S13 Silvia I'm looking for about $500 for that. Recipt for about 700.

Make you offer for everything else on the engine, or the engine itself. The engine did run but I blew the head gasket, and then snapped the cam shaft for the intake side. so its still a good running motor. VLT water pump ($60) and new R32 turbo radiator ($230)

Gearbox, Needs to be rebuilt doesnt like going from 3rd to second. Needs new clutch. I dont wanna take it out as I dont have the tools. so if you want it you can come and take it out and way for $50.

Parts located in Logan, PM me or RING me on 0407 578 896.

Brendan.

Edited by Rancher
Link to comment
https://www.sau.com.au/forums/topic/135635-rb20de-parts/
Share on other sites

Am willing to swap for a few things to suit my new engine and stuff. I'm after a boost gauge, air/fuel gauge. I want the ones that light up that really nice blue.

Am open to other things, depending

Link to comment
https://www.sau.com.au/forums/topic/135635-rb20de-parts/#findComment-2522715
Share on other sites

Bumping,

ECU to suite RB20DE $50

Reco head to suite Rb20DE $120

exhaust to suite RB20DE Silvia $500

VL Turbo water pump $60

R32 radiator $230

Intake manifold + new gaskets $150 (Will split)

rocer cover's to suite RB20DE $30 for pair

Exhaust Cam shaft to suite RB20DE $60

Gearbox, 2nd is crunchy 85% of time, $50 (You have to take it out)

RB20DE $300? make me an offer

Link to comment
https://www.sau.com.au/forums/topic/135635-rb20de-parts/#findComment-2523724
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...