Jump to content
SAU Community

Recommended Posts

hey all!

Got a pair of bride seat rails for the passenger and driver side for sale from an R34, they are second hand but practically look brand new. The code number is N105, i know they only fit in R34 and not R33s, dont know about R32s. They are currently on a pair of East bears R34 seats.

Pick up in sydney only plz, no postage!!

Price: was $500 for the pair!! $350 FOR THE PAIR!!! NOW $300!!!!!! FOR THE PAIR!!!

plz pm me for any other questions.

Cheers

Manveer

post-19396-1159585666.jpgpost-19396-1159585716.jpg

Edited by bLaCkMaN
Link to comment
https://www.sau.com.au/forums/topic/136561-fs-r34-bride-rails/
Share on other sites

lrc135 Posted Today, 01:59 PM

QUOTE(shonen @ 7 Oct 2006, 12:40 PM)

are these the super low rails ?

or the normal height ?

I would like to know the same.

hey, i have no idea whether they are super low, are there any other markings from the normal ones on them apart from being low itself?

Cheers

Manveer

GT51R Posted Today, 05:18 PM

for R34 GTR as i just tried 34 2wd in my 34 R and did not fit!!

a okz, thanks for that, there from a 2WD for everyone with that question!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...