Jump to content
SAU Community

Recommended Posts

Hey people,

Im after a bucket seat WITH rails to suit S2 r33. Must have a seating position lower then the standard r33 seat. If anyone could help me out that would be great.

Also, I dont want to spend mega bucks so any reasonable prices will be considered.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/137594-wtb-bucket-seat/
Share on other sites

Hey people,

Im after a bucket seat WITH rails to suit S2 r33. Must have a seating position lower then the standard r33 seat. If anyone could help me out that would be great.

Also, I dont want to spend mega bucks so any reasonable prices will be considered.

Cheers

Hey i have a pair of R34gt-t seats if that is of any interest...

Only waant $350 for them if that is of any interest....they will bolt in..

I am locaed in Newcastle..0412426573

thstnks brad

Link to comment
https://www.sau.com.au/forums/topic/137594-wtb-bucket-seat/#findComment-2562679
Share on other sites

Hey i have a pair of R34gt-t seats if that is of any interest...

Only waant $350 for them if that is of any interest....they will bolt in..

I am locaed in Newcastle..0412426573

thstnks brad

Hi Brad,

How are they compared to r33 seats?? the reason i need something with a lower ride hight is because im to tall to fit in with a helmet.

Also, seats must be RDA or what ever it is approved.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/137594-wtb-bucket-seat/#findComment-2562692
Share on other sites

Hi Brad,

How are they compared to r33 seats?? the reason i need something with a lower ride hight is because im to tall to fit in with a helmet.

Also, seats must be RDA or what ever it is approved.

Cheers

Hi these are standard seats so i don't know what the rules are..I don't know if they are lower but i have the same seats in my car if you would like a test run...I will try and find you a pic

post-27703-1160174034.jpg

Link to comment
https://www.sau.com.au/forums/topic/137594-wtb-bucket-seat/#findComment-2562698
Share on other sites

buy some GTR seats. Put some in my car (R32 GTR seats bolt right in) And they sit about 1 inch lower. (I'm short so it didn;t do me any favours) You can pick them up for under $800 per pair. Or just hunt around for drivers seat.

And they are ADR approved to the best of my knowledge since it is a factory seat(including the rails).

Link to comment
https://www.sau.com.au/forums/topic/137594-wtb-bucket-seat/#findComment-2574428
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...