Jump to content
SAU Community

Recommended Posts

hey gurls n gurls, i need sum help

i put my car on the dyno about 4 months ago at unigroup. it made 181.5 kw as seen by the printout. as you can see, the afr remains at 14 until 5500 rpm and then drops to 13 by 6000rpm and then to 12 by 6500 and onwards. Back then i had cat back exhuast, pod, front mount and close to 1 bar of boost.

Now i have a split dump/front pipe, high flow cat, fuel pump. last week i installed a power fc and got it tuned by hit man. As you can see it only made 175 kws? i was like wtf? he reckons sumthings really faarked cos it shud be closer to 190-200rwks. he recons maybe my cats melted cos my pump died and i was running really lean, however if u look at my afr now theyre really low...max is 12.5 but it drops away significantly.

i dunno, do u think i shud increase my afr to what it was before. cos even though it was 14, it dropped to 12 on high load and im thinking maybe thats safe?

newways my power is low and boost comes on slowly sumtimes, yet mid-range is now better? on low throttle, if i hold it at a certain point, i get this slight detontation. i dunno, any suggestions?

both graphs are there

cheers, anton

post-29367-1161416292.jpg

post-29367-1161416442.jpg

Link to comment
https://www.sau.com.au/forums/topic/139647-lack-of-power/
Share on other sites

the closer you get to 10:1 afr, the safer it gets

the reason it may have become richer is because of the extra airflow caused by the dump and cat, combined with the added fuel flow of the aftermarket pump.

What you get is a richer mixture causing less power (cos before you were lean)

someone please explain this better than me...

Link to comment
https://www.sau.com.au/forums/topic/139647-lack-of-power/#findComment-2602936
Share on other sites

just noticed your intake temp was 54 degrees. that may have something to do with it.

also i'd say your tune isn't the best. the graph is a bit crappy, but that could also be due to the fact you are losing quite a bit of boost.

and if it was run in 4th gear, they are backing off at about 6000rpm.

Link to comment
https://www.sau.com.au/forums/topic/139647-lack-of-power/#findComment-2603024
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...