Jump to content
SAU Community

Fs: Cefiro Bits/s13/c33/180 + Dish And Aftermarket Bits

Hella Flush
 Share

Recommended Posts

Hella Flush Experienced

Hella Flush

Posted
Posted (edited)

full 4 stud hubs brakes and stub axle setup front and rear

safety21/cusco 6 point full cage - good for street as it follows all roof and pillar lines

navy blue a31 unregistered/uncomplied 88' cefiro... factory 5 spd manual turbo... fresh 8X,XXXkm engine dropped in - gtr 33 cooler, gtr fuel pump, nismo clutch, eastbear cooler piping etc... many mods can come with it - pm for enquiry/package - has import approval so can be complied easily

fiberglass front and rear fender flares universal - arch type... with rubber seals and stainless hex bolts

random other ceffy shit... series 1 tailights with cefiro written in the middle

kei office front and rear coilovers - height and preload adjustable with front camber tops - need rear tops...

Edited by Hella Flush
NV N01 Experienced

NV N01

Posted
Posted
willing to ship thats no problems aslong as you pay for freight

It might cost a bit to send a whole car up with a cage and coilovers?

Hella Flush Experienced

Hella Flush

Posted
  • Author
Posted

photos can be found here of cage

http://i66.photobucket.com/albums/h252/1at...-10-06_12-1.jpg

http://i66.photobucket.com/albums/h252/1at...22-10-06_12.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      If there's enough meat in the housing where you want to put the M12 adapter, then do it, but be aware that if/when you f**k that up you'll probably be repairing it before doing anything else. I'd just drill it out and tap ina 1/4" thread. No need for rocket surgery when the next most obvious thing will do. You could throw a 1/4 x 1/8 bush in there and use the same fitting you intended to use.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Not this But this  
    • Murray_Calavera
      What should I do next to hold the head on

      By Murray_Calavera · Posted

      Is the only issue that the oil catch can is getting filled on hard runs? I'd be thinking more about oil control issues rather then the head lifting, especially as you aren't seeing spiking in the coolant pressure.  Do you need restrictors in the head, or better drains from the head? Does the sump need venting to the catch can?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      Tried to make 1/8npt threads into compressor house of the turbo for my EBC. Threads got fu#ked and ended up with and elongated hole, so I do have good amount and nice threads 90% of the hole but 10% I only had 1-2threads there and rest of it is flush on that side of the hole.. So my idea is to do M12 x 1.25 to AN4 with braided lines instead of 1/8npt to 4mm vacuum silicone hose.  and hopefully get a better thread. M12 is quite big and AN4 is a little bit bigger than 4mm (4.9mm inner diameter braided PTFE hose). but this should work. Thoughts? Otherwise I will weld and adapter onto the turbo.   
    • Duncan
      C34 RSFour V Build in the US

      By Duncan · Posted

      Looks great, I hope everything is working well after all that time!
×
×
  • Create New...