Jump to content
SAU Community

Recommended Posts

Hi all,

I'm selling a pair of ball bearing Garrett turbos to suit RB26DETT - GTRs. They come complete with 1bar rated actuators, modified oil drain flange pipes, and most gaskets, so all you need to fit is maybe a few gaskets and some patience!

I purchased these turbos not long ago, they're the only reason i'm selling them is that they're probably a little too big and therefor laggy for my current plans. That an i got an exhaust leak and i have had to remove them!!! ;):rofl: If sold i'll probably be going through the headache of a big single conversion.

Turbos are located in Townsville North QLD and i'll pay the freight to anywhere in australia if they're sold. and if i get a good price i'll even throw in brand-new un-used genuine nissan head-manifold gaskets.

They're rated at 320hp a piece and the part/chra number is 707160-005. According to the retailer that sold them to me theyre similar spec to the GT28RS but with smaller housings.

They come on like a freight train at 4-5k and above 5k they keep going and going.. They've never really gotten a proper chance to perform in my car, but I have done a 12.1 at 114mph with around 1 bar.. but they were maxing the injectors out pretty hard for most of the strip! Capable of soo much more!

Theyve seen less less than 4,000 kms of use i'd estimate.

If no one offers a reasonable amount they'll be refitted to the car.

More specs at :

http://www.turbobygarrett.com/turbobygarre...0R_707160_5.htm

I'm looking for offers around the $2,500 mark, which is lots less than what i paid not long ago. Call me and lets talk.

Please contact me, preferably ASAP and by phone, coz soon i'll be too tempted to fit them back to my car.

Call, 0402.701.181.

Cheers

Rob

Here is a picture of one of them next to my an original standard gtr turbo.

post-21092-1163219734.jpg

Link to comment
https://www.sau.com.au/forums/topic/142862-fs-twin-turbo-gt2560rs-near-new/
Share on other sites

A mate of mine tuned an R33 GTR, which had a pair of these and it managed an impressive 410kw at the wheels with these turbos on 1.8bar. This shows with a few mods these should be the last turbos you'll ever need to buy.

:pirate:

A mate of mine tuned an R33 GTR, which had a pair of these and it managed an impressive 410kw at the wheels with these turbos on 1.8bar. This shows with a few mods these should be the last turbos you'll ever need to buy.

:pirate:

wow thats unreal power! so would these be better than gt2860r with -5 version?

i can vouch for these turbos!

i have a set on my GTR and with a full turbo back exhaust and boost, the car ran 11.7 (on 4 occasions)

good luck with the sale mate - very good price!

cheers Garth

jebus, someone loan me the money. these would be perfect for my RB30/26 engine.

*shakes fist at buying house before finishing engine*

let me know if no one takes em before u refit them to your car, ill try and sell something or beg for money to buy them off you.

cheers

Daniel

Hi all,

I'm selling a pair of ball bearing Garrett turbos to suit RB26DETT - GTRs. They come complete with 1bar rated actuators, modified oil drain flange pipes, and most gaskets, so all you need to fit is maybe a few gaskets and some patience!

I purchased these turbos not long ago, they're the only reason i'm selling them is that they're probably a little too big and therefor laggy for my current plans. That an i got an exhaust leak and i have had to remove them!!! :no::P If sold i'll probably be going through the headache of a big single conversion.

Turbos are located in Townsville North QLD and i'll pay the freight to anywhere in australia if they're sold. and if i get a good price i'll even throw in brand-new un-used genuine nissan head-manifold gaskets.

They're rated at 320hp a piece and the part/chra number is 707160-005. According to the retailer that sold them to me theyre similar spec to the GT28RS but with smaller housings.

They come on like a freight train at 4-5k and above 5k they keep going and going.. They've never really gotten a proper chance to perform in my car, but I have done a 12.1 at 114mph with around 1 bar.. but they were maxing the injectors out pretty hard for most of the strip! Capable of soo much more!

Theyve seen less less than 4,000 kms of use i'd estimate.

If no one offers a reasonable amount they'll be refitted to the car.

More specs at :

http://www.turbobygarrett.com/turbobygarre...0R_707160_5.htm

I'm looking for offers around the $2,500 mark, which is lots less than what i paid not long ago. Call me and lets talk.

Please contact me, preferably ASAP and by phone, coz soon i'll be too tempted to fit them back to my car.

Call, 0402.701.181.

Cheers

Rob

Here is a picture of one of them next to my an original standard gtr turbo.

post-21092-1163219734.jpg

hi mate im not sure how much you paid for these turbos but when i had purchased them 8 months ago i paid $2200...i just looked through ebay and some1 is selling them for $2550 brand new.

but good luck with your sale

Sorry to the people who pm'ed i've been out of town for a few days.

I understand that 2.5k is a little on the exxy side what with the prices these are going for these days. And I'm willing to conceed that obviously its pointless expecting anywhere near the new price, but looking due to the fact that there is absolutlely nothing wrong with these units and added to that, the costs i have to meet to replace them means i could probably only go as low as $2300.

The only reason i'd be selling these is to convert to a single turbo setup and realistically i'm looking at over $4k to purchase what i need.

So I take it on board that $2500 is too much and i'll adjust the pricet to $2300.

Thanks for the replies.

Robbo.

  • 2 weeks later...

MrFlex the fact that these turbos retail for $2500 a pair has already been noted.. Please read the thread, but thanks for the bump.

Unfortuantly I've decided to keep them, after a few very good offers, Ive decided to keep them anyway. The cost to replace them is just too much for me at the moment, these are good turbos, just a little excessive for what i want at present.

Thanks again to the people who made legitimate offers.

Cheers,

Robbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...