Jump to content
SAU Community

Recommended Posts

Hello all,

Before you tell me to search I'll let you know that I HAVE searched and there was alot of data to digest and I did but because there was so many different questions and scenerios I was abit unsure, I thought it was best to just open a new thread to make sure.

I have a small amount of mild mods to my car (turbo back exhaust, ebc, fuel pump, fmic, fpr) and I plan to keep the car this way. I really would prefer 250rwkw as I believe this would be the just right amount of power to move our cars weight, but for now I'd prefer a realiable car with less problems - as we all know the power you have the more problems you are likely to run into.

I am going to build a Jaycar DFA in a few weeks and after alot of research I believe this is my best choice as I am quite happy with the cars power at the moment but would just like to remove the small flat spot I have at 5000rpm on 12psi and if possible, but not necessary, get rid of the REAL R&R (viscous surge).

So my question: Given the amount of mods I have would an Jaycar DFA do what I want to do? That is, to remove the flat spot(s) I get, and if possibly the R&R?

Cheers,

Andy

P.S - who should I ask to tune a DFA? Or should anyone with experience tuning an SAFC/PFC easily be able to use one when given instructions on how to use it? Alot of people have built DFA's; whats the feedback recieved from tuners?

P.S.S - please don't recommend a PFC. I've already decided I won't get one until, and thats if, I get a new turbo/injectors/afm setup. And seeing how Apexi no longer are making them it might prove hard. :huh:

The longer you wait the harder it is going to be to buy a Power FC.

Have a look in the Stagea section and you will find my thread on using a DFA, SITC and IEBC on a Stagea. I have no R&R.

:O cheers :rofl:

PS, the standard turbo won't last long at 12psi.

they dont directly avoid r&r, ie: the safc doesnt have a button to disable r&r it just happens that when it voltage clamps the afm values, you end up in turn avoiding the r&r protection. safcII is now discontinued as well, so you need to go safc Neo

Thanks guy, yep I was refering to avoiding R&R. As long as the DFA can do that I'll be happy.

I can't manage to find a PFC for an R34 GTT anywhere now at all, so I'll be on this path for a while until I manage to find one or look into the ECU remaps abit further.

I can't manage to find a PFC for an R34 GTT anywhere now at all, so I'll be on this path for a while until I manage to find one or look into the ECU remaps abit further.

Have you seen this in the For Sales section

http://www.skylinesaustralia.com/forums/in...amp;hl=power+FC

:wave: cheers :blink:

Because the turbine wheels are ceramic as oppose to the usual steel and as such don't take much boost/heat. The R34 compressor wheels are nylon as well.

Cheers for the link Gary but unfortunately that doesn't suit my car. It seems like the DFA is just what I'm after.

Because the turbine wheels are ceramic as oppose to the usual steel and as such don't take much boost/heat. The R34 compressor wheels are nylon as well.

Cheers for the link Gary but unfortunately that doesn't suit my car. It seems like the DFA is just what I'm after.

I realise they tend to delaminate from the shaft when the temps get up but with a safe tune I dont understand why you couldnt run 12psi through it with all the support systems? Series 2 R33's have nylon compressor wheels too champ.

Cheers

Chris

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...