Jump to content
SAU Community

Recommended Posts

Hey all,

The time has come to chase some more power :)

A.T.M I have 600cc injectors on the stock rail with a adj regulator in there and they have max'ed out on 17psi, so I'm after larger ones... looking at getting 800cc or 1000cc ones.

I've read cases of 1000cc injectors having idle'ing issues and can tend to 'drip' on idle? Has anyone using large injectors encountered this? is it even true or does it all come down to the tune?

I would like around 600-650awhp...

I think I did the sums right and the injectors should flow enough HP with the injector size.

800cc - 910bhp - 637awhp

1000cc - 1150bhp - 805awhp

I would like to get the 1000s for the 'safety' of having more flow/using less duty, but if it is going to more hassle than its worth I'll go a set of 800s.

Blitz 1000cc Injectors

Also will the stock fuel rail be up to the job with a nismo adj regulator? Seeing as the stock rail seems to have a larger inner diametre compaired to the aftermarket ones....

Thanks

Link to comment
https://www.sau.com.au/forums/topic/145561-injector-sizing-and-idling-issues/
Share on other sites

what power are you getting now to max out 600cc injectors, especially at 17psi

are you sure its not a fuel pump issue causing the duty cycle to be higher do to reduced flow from the pump?

I'm making 479hp @ all 4 on 17psi. The injectors were at 98% duty with a single intank 044.

600cc injectors should do more than 479hp, ur running to little fuel pressure, and yes running such large injectors as 1000cc will cause idling issues as the fuel wont be injected in as much atomised form as you would with 600cc with higher fuel pressure, many people make the mistake of running larger injectors than needed for their power needs , especially for a road car if idling is a concern.

get a rising rate fuel reg such as a malpassi etc, trust me youll get way more out of your 600cc injectors

I would like around 600-650awhp...

I think I did the sums right and the injectors should flow enough HP with the injector size.

800cc - 910bhp - 637awhp

1000cc - 1150bhp - 805awhp

its pretty much 1hp = 1cc for the 6 cyc.

800cc = 800hp, that allows for a bit of headroom aswell and takes into account enrichment and that sorta thing for acceleration.

Yo might get more if you bump rail pressures and what not.

If you want 650rwhp, you want the 800's, and what they dont make, just knock a couple psi of pressure into the rail

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...