Jump to content
SAU Community

Recommended Posts

what FMIC is that Wayne?

Actually I'm not sure specifically what brand :laugh: except to say it is one of the cheaper ones sold by Croydon Racing Developments - I also had them install it.

Seems to do the job - not much butchery involved save for a hole under the battery carrier.

Righto -

So bright and early(ish) yesterday I decided to go for a run down to Hobart from home (St Helens) if only to see what the roads are like.

The route along the east coast in brilliant over all, good quality surfaces, a good drivers road suitable for 'interesting' speeds. The only thing it lacks is a really tight/twisty section - but it has pretty much everything else you could ask for. I didnt spend much time in Hobart itself, once I spotted the towers up on My Wellington, I made a beeline for that tower :laugh:

So thats where these pics were taken anyway.

It was freakin' freezing up there (literally) and I certainly wasnt dressed for it either...

Also had a real fun time trying to disarm the immobiliser due to the high RF levels up there!

Too bad there is a lot of bug spatter on the front... just try to ignore that.

gallery_46181_2588_22026.jpg

gallery_46181_2588_41850.jpg

gallery_46181_2588_16147.jpg

gallery_46181_2588_16124.jpg

gallery_46181_2588_52918.jpg

gallery_46181_2588_6228.jpg

just an update guys

some shocking pics but here ya go

car made 300rwkw at 16psi last nite, will be pumping about 20psi and see how that goes, might even go for 25-28psi at the end =D

21042008070yc5.th.jpg

21042008068nf8.th.jpg

Edited by R34NRG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...