Jump to content
SAU Community

My 32 4 Door Drifter - Stadium Drift Pics And 3071r Pics * Check Last Page*


Recommended Posts

  • Replies 156
  • Created
  • Last Reply

Top Posters In This Topic

I bought a navara drive brand new from nissan, then knocked the roll pin out the body, pulled the shaft out and melted the cog off with an oxy, i then took the 33 cog off the 33 drive and modified the shaft to fit this cog (you cannot use the navara cog) basically the 33 cog has a half moon cut out on it, so i ground a half moon onto the shaft and then placed the cog on, drilled a hole in the base and put a roll pin in, then put the complete shaft back into the navara body and put the roll pin back in there.

easy process!

As for my clutch its a brand new exedy 5 puck....

haha yeah seems to work.

we ive got quite a lot of work ahead of me to get the car ready for G1 coming up... got to change the clutch with anoither new one, make sure thats all sweet, then remap and full dyno tune, wheel alignment, and fix up a couple of suspension issues lol.

fun times.

damn straight!!! im hoping for a good result as the car is performing very well now, Loads of torque, loads of grip, good tyres and wheel alignment... all thats left is the driver needs to make it happen hahaha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...