Jump to content
SAU Community

Recommended Posts

Make sure there are no reducers/step downs in the piping from the rocker covers to the can.

You want all the piping to be the same diameter as the hoses coming off the rocker covers.

Make sure there are no reducers/step downs in the piping from the rocker covers to the can.

You want all the piping to be the same diameter as the hoses coming off the rocker covers.

i dont htink step downs are bad as long as they are sealed properly and not letting out air.

do not block the pcv valves on the rocker, they vent so there isnt a build up of pressurised air in the rocker.

i dont htink step downs are bad as long as they are sealed properly and not letting out air.

do not block the pcv valves on the rocker, they vent so there isnt a build up of pressurised air in the rocker.

absolutely wrong - you can block the pcv on a turbo car, as the gasses just pass through to the catch can and then vent to atmo, or are plumbed back to the turbo>afm pipe

If you block the pcv, you may need to adjust the AAC valve so the car will idle correcltly though

RB engines breathe a fair bit, using reducers on the pipes to the catch can, or after the catch can, can cause crank case pressurising problems - but will probably depend on the degree of blockage, how fresh the engine is, and how much power you are making

best not to have any reducers.

does the catch can plumbing still have the pipe that goes to just after the afm? i have seen this pipe removed when people have installed catch cans so the motor is getting unmetered air.

if the new setup has a filter on the side that is sucking atmo air, not air from after the afm, then i'd say that is the problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's not any meta data. They have scraped images from everywhere, and then use AI to compare your photo to other photos and work out where you are.
    • I just looked at my camera phone settings, apparently I have "not allowed" for location  Will that stop that app?
    • Can you not just turn it off on your phone if required? I remember a brief on this, well, I remember the brief, not what to actually do. LOL
    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
×
×
  • Create New...