Jump to content
SAU Community

Recommended Posts

im selling my direct port nitrous kit complete with lines bottle everything needed to fit comes with a full bottle of gas and is jetted to 108hp 6 cyl kit can be used on 4 cyl and rotor aswell

price $950plus freight

ring jason on 0424348521

how easy are these kits to install?

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2797970
Share on other sites

  • 1 month later...

hi

is this kit sold yet? where are you located?

is it the direct port fittings that sit under each injector or a fogger tapped into the manifold near each cylinder?

thanks

Justin

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2897928
Share on other sites

  • 3 weeks later...

kit comes with 10 pound nitrous bottle

braided main nitrous line

nos solenoid

fuel solenoid

6 seperate direct port foggers with jets

braided lines from solenoids to distribution blocks

and solid lines from distribution block to foggers

kit is complete ready to use

freight will be no probs anywhere in aus or tasmania

new price $800 plus freight

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2938400
Share on other sites

600rwhp 15 psi no gas

the reason for sale is the nos was to get the turbo onto boost with a 4500 rpm stall converter as street registered car ran 9.3 @141mph

the new engine runs a methanol motor with a 5200 rpm stall converter and 2 step so no need for the gas anymore

nos was also used to win dyno comps which im also not interested in anymore

Edited by jas/slo32
Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2950486
Share on other sites

600rwhp 15 psi no gas

the reason for sale is the nos was to get the turbo onto boost with a 4500 rpm stall converter as street registered car ran 9.3 @141mph

the new engine runs a methanol motor with a 5200 rpm stall converter and 2 step so no need for the gas anymore

nos was also used to win dyno comps which im also not interested in anymore

Have left message on your phone and sent pm , please call me - thank you :(

Link to comment
https://www.sau.com.au/forums/topic/149538-sold/#findComment-2953560
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...