Jump to content
SAU Community

Recommended Posts

i got some vs work wheels for sale 1600 o.n.o

i would like 1600 for them but reasonable offers considered for quick sale

the stud pattern is 5x114.3, 18x8 offset is +38 would require spaces to fit a skyline gts-t fronts only also might need guard to be rolled 255 rears

plaese note: there is no gutter rash on any wheels

in excellent condition

tyres are about 80% + in sydney

2 x falken 225/35/zr18 front

2 x falken 255/35/zr18 rear these tyres cost 1200 new, no wind noise like nakang tyres make

they've been balanced not fitted to car yet

they are 2 peice rims might be 3 not sure

would also swap for wheels with lots of dish, i want very japanes 2,3 peice deep dishes like 10 inch wide and 12 inch back plus cash you way

thanks, josh

also note: the outer dish is from another car 5x120 it says but the centre is for merceds, rx-7,skyline s15 silvia 200sx etc may requires spacers for skyline gts-t front only see pics

post-25554-1168132817.jpg

post-25554-1168133014.jpg

post-25554-1168133383.jpg

post-25554-1168133678.jpg

post-25554-1168133982.jpg

post-25554-1168135502.jpg

Edited by ijoshi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...