Jump to content
SAU Community

Recommended Posts

Can anyone give me a idea how much it will cost and who to use to get a gear box from silverwater sydney to richmond adelaide. GTR getting new box and if its cheaper than $400 then it's money in my pocket saved

Any help would be appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/150003-sydney-to-adelaide-transport/
Share on other sites

i would imagine is would be less than 400 to get it here...tell them to wack it on a pallet and get it couriered to your door. through someone like TNT or HI-TRANS or bluestar..something like that...

a whole car costs around 4-500 to get state to state so i can't image it would cost anymore than that.

Thanks for the reply's people. :P

The reason I was asking is because I can get a brand new gear box from advan in Sydney for $3000 and over here in adelaide nissan wants $3800 but will give it to me for $3400.

therefor if I can get it here cheaper than $400 , the change is in my back pocket not nissan's :w00t:

plus more money towards the clutch

:O

Thanks for the reply's people. :(

The reason I was asking is because I can get a brand new gear box from advan in Sydney for $3000 and over here in adelaide nissan wants $3800 but will give it to me for $3400.

therefor if I can get it here cheaper than $400 , the change is in my back pocket not nissan's :)

plus more money towards the clutch

:P

hmmm. thats expensive...have u considered going to someone like ppgearboxes and asking them what strong rebuild with yours would cost? thats alot of money...

To answer your question regarding rebuild cheaper option. You tell me what you would do if a new box cost's $3000 or just for the bearings it will cost $2600. The input shaft is making a racket and you need to get every bearing out to get to it. Plus I've been told redoing the bearing's might not get rid of the noise anyway.

By the way , the car does put out 297rwks and to rebuild properly with ppg would cost $9000-$10000 anyway or a holinger is $20000 approx

Edited by savage GTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...