Jump to content
SAU Community

Recommended Posts

Few things i need to get rid of:

H&R Bolt-on wheels spacers (2 only)

- (Used, came off 350Z) PCD 114.3 they are 25mm thick,

as you can see they have a centring peice (which alot of spacers dont)

Price: $100

Pics:

spacer1nz6.th.jpg

spacer2tu9.th.jpg

======================================================

R32 GTS-t Standard rims and tyres

Stocko rims 114.3, 90% tread / slight gutter rash....custom mat black >_<

Price: $170

======================================================

ADVANTTI 18" Rims and tyres

Brand new set of Advantti rims 18" x 8 / PCD: 114.3

new / never used

fits: Nissan, toyota, ford, mitsubishi

Tyres are brand new Neutons 235 /40 /R18

Price: $1400

Pics:

wheel18pk0.jpg

rimsxd8.th.jpgrims2jf2.th.jpg

=====================================================

Set of 4, 19 X 8 Rims and tyres Gunmetal centres with Machined lip

PCD 114.3 Suit Ford, nissan, mitsubishi, toyota

Used one week, no marks, like new

Pirce: $2000

pics:

gtrsidesi1.jpg

gtrreargf8.jpg

Reason for sale: Brought new wheels

Edited by -GODZLA-
Link to comment
https://www.sau.com.au/forums/topic/152105-rims-tyres-16-18-19/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...