Jump to content
SAU Community

Recommended Posts

Hey guys, I scratched my gtr the other day on the rear bumper and tail light. Absolutely filthy with myself!

Anyway, It'll be repaired properly down the track coz it needs some minor cosmetic work done. But, does anyone know where I can get some Gunmetal Grey (KH2) touch up paint to conceal the scratch a bit.

It does my head in every morning when I see the car. I need help!

Link to comment
https://www.sau.com.au/forums/topic/153061-gunmetal-grey-touch-up-paint-help/
Share on other sites

If you told us your location it would help.

If you want a good match go to Panelbeater supply shop with the paint code and a sample ( fuel lid door). They will mix it and colour match it in acrylic .

If you told us your location it would help.

If you want a good match go to Panelbeater supply shop with the paint code and a sample ( fuel lid door). They will mix it and colour match it in acrylic .

Im in the eastern suburbs of melbourne.

How much would a small amount cost if I did like you said and went to a panel beater for a colour match?

Im in the eastern suburbs of melbourne.

How much would a small amount cost if I did like you said and went to a panel beater for a colour match?

Go to panelbeater supply shop not a panelbeater, I don't know where to send you in Melbourne, if you was in Sydney I could tell you .

It should cost you about $15-$25 for 1/4- 1/2 lt then you will need some thinners too, some shops will put it in pressure pack cans as well, if you don't have a spray gun .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...