Jump to content
SAU Community

Ssr Vienna 19 X 9.5" & 10" Deep Dished Wheels With 285/30's

NXTIME
 Share

Recommended Posts

NXTIME Grand Master

NXTIME

Posted
Posted

Item: SSR Vienna 'Courage' 19 x 9.5" & 10" deep dished wheels with 285/30 Bridgestone tyres ($800 each new); fronts have +30 offset but come with new 15mm bolt-on spacers to make offset +15; rears are +11, O disk.

Unfortunately, these wheels won't fit my R32, but will suit R33/34 GTR's.

Location: Sydney/Wollongong

Condition: Excellent

Price: $3,300 ($8,000+ new)

Payment: Pick up or Direct deposit. Buyer to arrange and pay for postage

Contact: PM or post here.

Other: More pics can be provided. Other tyre sizes available. Lips have been machined to removed gutter marks.

post-4183-1169721265.jpg

post-4183-1169721286.jpg

post-4183-1169721307.jpg

humz Proficient

humz

Posted
Posted

lovely rims

just wondering if you would swap a set of Super advan racing version2 wheels 18x9.5 all round (some low gtr offset) with tyres for yours without tyres?????? mine are also black with a black dish, red writing in the centre cap, and gold nut over the top????

http://www.fizzautosports.com/rim/rim_advan_r2.html

NXTIME Grand Master

NXTIME

Posted
  • Author
Posted
Whats wrong with guard lipping?

is it both expensive and damaging to the car's paintwork?

Not if done properly/professionally. Cost is about $50/guard.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...