Jump to content
SAU Community

New guy...


Guest Skyline Fan 01

Recommended Posts

Guest Skyline Fan 01

Hey everyone,

I'm new to this whole forum thing, so I've got no idea really what i'm doing. Guess i'm just tryin to find my way around.

One thing is i know basically next to nothing about cars. That is, the insides of them, like engine specs and all that. So, if anyone can give me a run-down of what all the fancy terms mean, then that'd be nice.

If any1 has any pointers 4 me about forums (this 1 in particular obviously) then it'd be greatly appreciated.

Also, I've got around 17-20k for my first car. Any suggestions?....Doesn't matter what. Doesn't have 2b a Skyline necessarlily.....but preferably, of course.

Anyway, thanks heaps.

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

if u arent really concerned about what car u get then you should just consider the economic and use factor, will u use it everyday, how far will u travel etc. Skylines do tend to be a bit heavy on the ocket for petrol, specially if u just lurrrve pushing that accelarator. i suggest sum front wheel drive toy, good fun, handbrakies are good fun too hehe

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/#findComment-314624
Share on other sites

Guest Skyline Fan 01

ok cool......thanks for that everyone....that kinda gets me started in the right direction. At least i've got some idea of what to look for now.

I'm still not sure how much i'll have to spend, cause i'll have to wait as the olds are tradin' in mums 2001(?) pulsar +, so i'll have to just see, but that's the rough amount.....

And i'll definately be asking about what some terms mean, cause my friends know their car jargon, but like i said, i've got no idea, so thanks heaps for that as well.

Also, what's the easiest way to tell the difference between the R33 and R34 Skylines?

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/#findComment-315111
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...