Jump to content
SAU Community

Recommended Posts

The biggest problem I can see with that idea is creating an area for sufficient runoff at the end should anything go wrong - the strip would have to be moved down substantially, and it would cease to be a part of the racing circuit.

I don't know the layout that well, but based on a map pic, I can't see why not.

http://web.archive.org/web/20041208141249/...et/circuit.html

Aerial photo.

post-11737-1170140709.jpg

The darker area is the strip yeah, and runs from right to left?

Looks like there's plenty of room further left to me...

Ash, from what i understand..... it would be rotated 90 degrees, but now that chops has brought that up maybe their thoughts are to run it west to east not east to west as it currently is! But maybe there is more land than what we see there! it sure sounds like a good idea to NOT race into the sun tho!

Edited by Deluxe

You see there is about the strip length again at the end of that strip, then the runoff area after that (sandy).

I'm not sure they'd get approval to run it towards the road - if anything went wrong with a top fueller it could potentially head towards the road, rather than away from it into vacant land as it does now.

Also, I'd rather it opened sooner than after a full rebuild - I'm considering selling my car with no place to race.

EDIT: typo central

Edited by chops

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...