Jump to content
SAU Community

Recommended Posts

ok guys D3 is gunna be a huge event all details will be put below:

WHAT IS IT?

DRC dyno day compitition

WHEN?

17th febuary 2007

WHERE?

DRC's workshop

39 Rookwood Road Greenacre

TIME?

7pm til 4am

HOW MUCH?

$50 which includes three dyno runs and one dyno print out

PRIZES?

1st prize:

full dyno tune + remap + choice of computer valued at $1200

2nd prize:

full performance service (oil, plugs and filters) valued at $550

3rd prize:

three dyno runs

**THIS IS AN AWD DYNO SO ALL ARE WELCOME**

also D.J AKAY will be mixing it up with a special appearance by IGNITION DVD, FAST FOURS and arabian HIPHOP sensation 'M.I.B'

D3-2.jpg

evan if u dont want 2 enter ur car just come down and check it out it will be a top night......

see u there.........

Link to comment
https://www.sau.com.au/forums/topic/153873-flypromotions-presents-d3/
Share on other sites

  • 2 weeks later...
i tried looking up the adress on whereis does this place exist.can somebody help

Hi mate I had the same problem the first time I went there the suburb they say is Greenacre but it is really in Yagoona try that suburb you should find it mate. :laugh:



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...