Jump to content
SAU Community

Recommended Posts

Hey,

I've had a problem I have been trying to sort out, that is the car popping/misfire on load at 4000RPM and above. I have cleaned the AFM and put in PFR5G spark plugs in.

I have fixed the problem from misfire from 4000RPM - 6000RPM from there it will pop and hesitate between 6000RPM - 7000RPM before changing gear (automatic)

Any ideas?

Edited by ThugishPimp
Link to comment
https://www.sau.com.au/forums/topic/155639-quick-question-please/
Share on other sites

well 5 heat range is too hot, most use 6

checked your coils for cracks? boost below 12psi?

Thats what I thought. Stupid Autobarn.

Would having the heat range at 5 cause this to happen? I've been told by many to use the heat range 7.

I'm running stock boost, coil packs are fairly new spitfires.

Thanks for your help Craved!

I have tried BKR6E also and had the same problem. After I cleaned the AFM I only had the misfire from 6000-7000RPM and not 4000-7000RPM.

I have been told to try heat range 7. I got a set of BKR7E. Should I give it a go? Only mods are; Modifications:

- K & N Pod Filter

- Cold Air Intake

- Forged Pistons

- Strengthen Conrods

- Blueprinted

- Balanced

- Port Polished

- Metal Head gasket

- Spitfire Coils

- High Performance Timing Belt

- High Performance Spark Plugs

- Gready Turbo Timer

I've put in all new BKR7E spark plugs. Took it for a run it popped/misfired between 6000 and 6500RPM then changed gears, didn't seem as bad as it was when it was popping/misfiring between 6000 and 7000RPM.

Went to a friends after taking it out, on the way back I wanted to see if it would still do it, and I had no problems.

Now, here's the problem;

This has happened before, it will miss/pop then run fine for 1-2weeks then it'll pop/misfire again.

I can only hope the heat range 7 plugs doesn't cause it to pop or miss in a couple of weeks.

Any comments, suggestions?

what fuel are you using out of curiosity ?

V Power Racing (100% with 5% ethonal)

is it in tune? That could also be an issue, trial and error. Changed fuel filter? Any knock? Injectors? O2 Sensor? hmmm run out of others.

Not sure

Adam

I've had the fuel filter checked, no knocks, injectors have just been cleaned. Not 100% sure on he 02 sensor, but when it was in the performance shop they said they checked everything.

They said it was most likely my coil packs but since the rebuild had just been done then I couldn't get it on the dyno and rev it too high.

well 5 heat range is too hot, most use 6

5 is the standard heat range. if you're running close to standard power then colder plugs shouldn't be necessary.

Edit - popping and misfiring is very likely to be tired coil packs. Gap your plugs down to 0.8mm and give it another shot :huh:

Edited by Kinks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...